Recent content by GenoBluzGtr

  1. G

    Increase Pedal output gain

    try using single-pin sockets for that resistor so you can easily and quickly swap resistors.
  2. G

    Paragon

    I've built three of these. One with "norm" on both channels, and one each with High Gain Mod on Right / Left Channels. Works great, you just have to adjust your thinking about what "high gain" is... in this case it's NOT much extra. even the original Analogman KoT advertises the "high gain"...
  3. G

    Paragon - "Euphonious Rex"

    I finally got around to building one of these (I've had several boards for some time now, but kept putting off sourcing the hard-to-find parts. I'm really impressed with the tone of this build - I've played KoTs before (my band mate has 3 of them!), but never appreciated the tone until now...
  4. G

    Analog Spring Reverb Pedal

    Awesome approach.... rather than saying it's a "big pedal", I would say rather "the smallest true spring reverb ever!"... Great job!
  5. G

    "Old Glory" (glory hole overdrive)

    Thanks All!!!
  6. G

    "Old Glory" (glory hole overdrive)

    VERY impressed with this pedal. The tweaks to the original Blues Breaker circuit are just right, nothing that wasn't needed. Slightly more gain, a good bit more available volume (the original Marshall BB couldn't reach unity unless your gain was above noon!!), and a toggle to cut the high end...
  7. G

    Brown betty - no sound

    I just fixed an issue where my power LED would not turn off. Not sure if it's related to your no sound issue, but for me the issue was that too much Solder flowed through the lugs of the footswitch and I had a solder bridge UNDERNEATH the 3PDT breakout board that I used. However upon...
  8. G

    Angry Charlie V3

    Great looking build! FWIW, you MAY want to try the "Guvernator"... the Angry Charlie is based on the Marshall Guv'nor circuit, and one of the things that Josh did with the AC was add some extra gain and lower the low-end response (maybe he took center of the midrange down?). It makes the AC a...
  9. G

    Triple Drive/Boost - Bluesbreaker / Zendrive / SHO. Reverse order

    Thanks so much! I am constantly looking for combinations of drive pedal that stack well... as a cover band guitarist, I try to cover as much ground as possible tone-wise with as small a rig as I can... When I built the Mahayana (Zen), I knew it was a fantastic middle-of-the-road (grind-wise)...
  10. G

    Triple Drive/Boost - Bluesbreaker / Zendrive / SHO. Reverse order

    Thanks, guys! I think it turned out better than I hoped for. Love it when an idea not only comes together, but exceeds expectations!
  11. G

    Triple Drive/Boost - Bluesbreaker / Zendrive / SHO. Reverse order

    Here is one that I built for myself. 25+ years of gigging and I have ALWAYS hated that the typical "order" of multi-drive pedals usually have the lead/solo boost on the left side of the pedal. I am right footed, and, especially when singing, I've always felt awkward crossing over to the left...
  12. G

    Phase II - High pitched noise that follows LFO of the LED

    There are no dust covers on those pots, are you sure.... 1. There is not contact on the back of the Circuit board with the metal pot bodies? 2. That "IN" jack doesn't spring down when a jack is plugged in and touch the metal pot body underneath it? - EDIT: Nevermind this one, after watching...
  13. G

    SOLVED I was on a roll... :( ... General Tso

    Chuck is a damned wizard, I tell you. Kinda scary how tenacious he can be. Glad to see this one sorted out!
  14. G

    wiring a Footswitch (or dual footswitches) to get an "either / or" set up in one enclosure

    Awesome! That could work... Thank you!!! This is perfect for a dual delay or a dual reverb, then!
Back
Top