Recent content by PedalGuy

  1. P

    ElectroVibe Noise Issue

    Yes sir! A 1 Spot Pro CS7.
  2. P

    ElectroVibe Noise Issue

    Unfortunately I have not been able to fix it and after a few weeks of troubleshooting I'd just accepted "defeat". It might be the charge pump; that's about the only thing I have not yet tried messing with. I might just try ordering one from (hopefully) a different batch.
  3. P

    ElectroVibe Issue

    True... But I have already done that on my Aion Nucleus (Colorsound Powerboost) build and don't want to connect both pedals to the same output.
  4. P

    ElectroVibe Issue

    Update: The new transistors did not solve the noise issues I was having. I used a 470 pF cap across R8 for now as I currently don't have any spare 100-220 caps (they should arrive tomorrow). That has drastically reduced the noise with the fuzz knob turned all the way up (or down technically...
  5. P

    ElectroVibe Issue

    I'm using a power supply (1 Spot Pro CS 7). The noise only seems to affect the dry signal as it is VERY quiet in the vibrato setting. I need to turn my amp way up to even hear it. On the chorus setting I can just about hear the noise at "bedroom playing" levels. I could try using a battery...
  6. P

    ElectroVibe Issue

    The high pitched noise is still present though! I don't know how old you are @Big Monk but according to my research you should still be able to hear this pitch well into your 40s maybe 50s depending on your lifestyle (e.g. being a musician) etc. I know for certain that there is an annoying 12kHz...
  7. P

    ElectroVibe Issue

    I'm just an idiot! I had the intensity turned all the way down... Well the effect is working now. If only I hadn't ruined that pad... Then again; it's not like that limits the functionality of the pedal it just doesn't look too great.
  8. P

    ElectroVibe Issue

    I'm getting lower voltage readings than expected with: 8.65V instead of 9V on the charge pump (pin 8), 15.7V instead of 18V on C11, 12.17V instead of 15V on the voltage regulator (output with 15.32 on the input) and around 15.7V on the lamp instead of 18V (with my current trim pot settings). Are...
  9. P

    ElectroVibe Issue

    I probably should take a break but I don't understand why the Vibe "randomly" stopped working; I had it in the enclosure working properly. Then I put the screws in and the effect didn't work anymore. I thought that maybe one of the capacitors was damaged but the only "tall" caps are C22, C11 and...
  10. P

    ElectroVibe Issue

    Well... I tried replacing components and broke the PCB (two of the pads are gone). I used jumper wires but the lamp still won't oscillate, so it's probably not the capacitors or resistors causing this issue.
  11. P

    ElectroVibe Issue

    Unfortunatly I "broke" the Vibe; I put it back into the enclosure but some capacitors were sitting to high/low. I was able to press down hard enough to get the screws back in but now the lamp is not oscillating and I'm not getting any signal when the effect is engaged. Any ideas? Edit: It takes...
  12. P

    ElectroVibe Issue

    Guitar->ElectroVibe->Twin Face->18V Colorsound Powerboost replica (with some mods)->Hydra Delay->Amp or Audio Interface. After reflowing the solder on the LDRs the oscillation noise has now improved a little (I think).
  13. P

    ElectroVibe Issue

    "vibesolo" is the vibe with no other pedals connected. "vibenoise" has some other pedals connected (Big Muff and bypassed hydra delay). Edit: "VibeSilicon" = Vibe + Silicon Twin Face Edit 2: I've just uploaded the EQed file.
  14. P

    ElectroVibe Issue

    Maybe turn the volume up? Or perhaps you are too old ;) Anyway... I have just used an audio probe and LDR2 is producing a really strange modulation effect/noise which sounds exactly like the effect I'm hearing with my silicon fuzz connected. Edit: It is very subtle but there is a very high...
  15. P

    ElectroVibe Issue

    Update on the ElectroVibe: C22 (Power) seems to be damaged. Could that be the issue? Could replacing it with a new cap solve the issue?
Back
Top