Forums
New posts
Search forums
Media
New media
New comments
Search media
Resources
Latest reviews
Search resources
What's new
New posts
New media
New media comments
Latest activity
New resources
Members
Current visitors
PedalPCB.com
PedalPCB Wiki
Log in
Register
What's new
Search
Search
Search titles only
By:
Current visitors
Menu
Log in
Register
Install the app
Install
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
P
PJS
Active member
Joined
Jul 20, 2020
Last seen
48 minutes ago
·
Viewing thread
What Would Fry a Zener Diode?
Messages
249
Solutions
1
Reaction score
210
Points
43
Find
Find content
Find all content by PJS
Find all threads by PJS
Latest activity
Postings
About
P
PJS
replied to the thread
What Would Fry a Zener Diode?
.
Before catching fire they get this really nice red glow happening
Yesterday at 11:07 PM
P
PJS
replied to the thread
What Would Fry a Zener Diode?
.
I lost the 15V zener that was regulating power to the EQ board in my bass amp once. In that case a very very hot signal had fried all...
Yesterday at 7:21 AM
P
PJS
replied to the thread
Pro-10 Dual Overdrive Help
.
The pots we can see look as if they are insulated on the back with electrical tape. If that is the case that may well be your problem...
Thursday at 6:07 AM
P
PJS
replied to the thread
Mini-Heterodyne not going well
.
With these, the trick is usually to look from the end. One side will be straight up and down (or close to). The other side will be a...
Wednesday at 4:32 AM
P
PJS
replied to the thread
Pro-10 Dual Overdrive Help
.
Photos of the solder side will probably help. Given that one side is working, your power is probably working, unless there is a...
Wednesday at 3:44 AM
P
PJS
replied to the thread
Ocelot Octave subtle distorted sound
.
I am not sure if this matters or not, but the only difference I can see that is in the audio path that is common to all the octaves is...
Aug 2, 2022
P
PJS
replied to the thread
SOLVED
Magnetron screw up
.
90% of the time if a pedal works out of the box and doesn't when it's in the box, it is either bad offboard wiring, or something...
Jul 29, 2022
P
PJS
replied to the thread
Busted TS9 - Troubleshooting
.
I think that in your situation before I replaced anything more I would trace through with an audio probe just to see what happens to the...
Jul 25, 2022
P
PJS
replied to the thread
SMD screamer
.
The photo isn't clear. I am a bit sus of the soldering on the transistors, but it is hard to tell. What voltages are you getting on...
Jul 23, 2022
P
PJS
replied to the thread
Kliché Mini - Low Gain, Very Loud
.
What behaviour are you seeing from the gain control? The gain on this does 2 things. It increases the gain (which should introduce...
Jul 16, 2022
P
PJS
replied to the thread
Busted TS9 - Troubleshooting
.
If you have 2 identical resistors to make up a voltage divider, and the divider is not giving you half voltage then there is a lot more...
Jul 16, 2022
P
PJS
replied to the thread
Busted TS9 - Troubleshooting
.
There are a couple of tantalum caps on the board. If they are C5 and C6 then they are polarised - tantalum caps are definitely polarised.
Jul 16, 2022
P
PJS
replied to the thread
Spirit Box doesn't do anything
.
I am guessing the capacitor doesn't fit. It looks as if the leads are not touching anything they shouldn't, but you are just asking for...
Jul 14, 2022
P
PJS
replied to the thread
Kliche Mini voltages are not right!
.
The numbering of the pins in that picture is the standard numbering used by every manufacturer and every engineer in the entire world...
Jul 11, 2022
P
PJS
replied to the thread
Kliche Mini voltages are not right!
.
OK. IC1 pin 4 should be ground - this is correct IC1 power pin (8) should be at 9V (or close to). At 0.3V this is way wrong. You are...
Jul 11, 2022
Loading…
Loading…
Members
Top