Search results

  1. B

    Best 2 in 1 drive combos?

    I’ve only done a single 2 in 1 so far (two sticks of doom and an amentum boost). but I’ve placed an order with a bunch of drive pedals and am curious about what people would combine. Mercurial Boost Box and All EQ Soldat Distortion Graphite Distortion Chop Shop Greengage Overdrive My first...
  2. B

    VFE Klein Bottle Redesign pre-orders

    Sounds like VFE is doing one final revision to his circuits before stopping all production of his own. With that, pre-orders for a revised Klein Bottle have started. $129 for DIY kit. Includes custom pots, smd soldering already finished, and pre-drilled bare enclosure. Not sure if he is capping...
  3. B

    Parentheses Fuzz

    Had the board sitting around completed while I tried to figure out the artwork. Finally, after rewatching some old Godzilla films again, I found a great artist named Attack Peter who does woodcuts of pop culture monsters. Woodcuts being a cousin to etched metal printing, these types of images...
  4. B

    Elk Big Muff Sustainar

    Bought 3 big muff circuits to make the Mask Us, a Green Russian and after seeing Nostradoomus talk about the Elk Gakki clone, I went and did some research and found that one of my favorite guitar players, Wata from Boris uses one. Super simple build to knock out while watching American Gods...
  5. B

    SOLVED No output from Duo-phase, Phaser B

    Using an audio probe, I traced the signal loss to resistor 29b (560 ohm) the phased signal comes off of C14B, but doesn't leave R29b to the output. I replaced it with a tested one, and still no luck. Phaser A's equivalent R29A works just fine and that side of the phaser functions as normal...
  6. B

    Last two builds of 2020 (Deflector Reverb and veroboard Lastgasp Laboratories Rattle Crow)

    2020 ended for me with some frustrating debugging still left to do. But the last two I boxed up with artwork finished were the Deflector Reverb, which is pretty nuts, especially compared to my Spirit Box. The Rattle Crow was my third veroboard build, as you can probably tell from the mess of...
  7. B

    Delegate compression LED not lighting up.

    I get sound in bypass and when the effect is on (level knob works great!), but I wasn't getting any compression. I noticed the LED didn't seem to be illuminating when i opened it up. When plugging in the dc jack, it initially lights up, but then fades, and no signal seems to cause it to...
  8. B

    Delegate Compressor (Boneyard Edition) optional diodes D6 and D7

    On the silkscreen they are D6 and D7. but on the schematic, they look to be D1/D2, Am I correct in thinking they are indicator LEDs for the compression ratio?
  9. B

    Deflector Reverb (hiss as density knob is turned ccw)

    Good morning (for me that is) everyone! I just finished the Deflector reverb and it sounds great, minus one issue I encountered. When density is closest to 7 o'clock, there is a loud hiss introduced to the signal, and gradually diminishes until completely gone around 4. It's more noticeable as...
  10. B

    Beautiful Girl, Play the Effector! (official title)

    Now that I have your attention with the weird title to this, let me explain... Digimart is a musical instrument inventory website for Japan and also has it's own "magazine" on the website. There are some really cool sections/articles, including interviews with various professional musicians and...
  11. B

    Suggestions for next builds? What do you like?

    So I've built or have them on the bench next: Arkaim Death Cap Sherwood Chalumeau Blender Organ Donor Little Green Scream Machine Master Fuzz (Nostradoomus spec) Zapper Pitch Witch Muroidea Distortion Obsidius Preamp Two Sticks of Derm + Amentum boost Sea Horse Trembling Loon Tremolo Cataclysm...
  12. B

    Maybe time to finally post some builds

    I've been building pedals since September of 2019 when I ordered the Death Cap and Arkaim kits through Musikding, but since it was going to take forever, I bought a BYOC CE-2 off Amazon Japan to build while I waited... After that, I realized it would probably be better to source my parts like...