Search results

I'm currently working on modding a Pitch Witch. I have one built and it works great. But I assembled it on my breadboard and it works, but there's a loud clicking with the LFO. I've never really messed with anything using an LFO before, so is there something obvious that I'm missing?

I just wrapped up an ocelot, and it seems Ok except the volume of the 2 octaves are very low. The normal volume works fine, just the octaves are very low comparatively. I’ve never played an original to compare this to, so I’m wondering if there’s an issue somewhere, or if the lower volume is...

Not sure if this will work, or be good/useful but I figured I would ask before I did something that could cause damage. I had an idea to add a sag feature to a Tone Vendor to simulate a dying battery. I was going to add a b10k pot and a 220uf capicator between the 1n5817 and pin 1 of the...

I recently build an OCD and Rat in 1 enclosure with an order switcher, and everything is working as it should. However, the output seems rather low. Where a normal ocd would be at 12 o’clock, mine has to be pushed to almost 4 to reach the same volume, and some of the high end that’s in the...

I'm working on a Distortion 250 on my breadboard and want to make some mods. One complaint I have is that the gain pot is a B1M and as it sweeps it doesn't change much then gets real dirty in the last 10%. If I want to make the sweep more gradual, would I change the value of the pot or the...

I'm doing a 2 in 1 pedal with an ADHD and Muroidea and I have a 3PDT switch pcb to swap the order. Is there a way to incorporate an LED so that you can tell the order of pedals when they're both engaged? If so, how would you go about wiring that? thanks.

Hey, it’s my first time using a breadboard, and I’m trying to tinker with a distortion plus circuit. Everything is wired up and it seems to be working, however, when I get the volume pot all the way up, it kills the signal. Any idea what may be causing this? Thanks in advance.

Just curious what some of you have been using to do artwork on your pedals. I've been going the JHS route and using rubber stamps with stazon ink, but I'm interested in trying other things. Any suggestions?

This may be a dumb question.... so I understand the difference between A B and C pots, but what decides the value of individual pots (example: A100k or A50k) in circuits? what would happen if you were to use a B1M in place of a B10k? thanks in advance!

Does anyone have any experience using a more available replacement for a 2n1711? What would you recommend? Its for a Cross Contaminator (Dirt Transmitter)

I am putting together a Twin Face, and I was curious if I could use a 4pdt latching footswitch in place of a 4pdt toggle to be able to switch settings mid song. In my brain I think it'll work, but I just wanted to put it out there before I did something crazy wrong. thanks

Hey, I just completed my 2nd twin face fuzz. First one came out perfect. 2nd one works when the toggle switch is up (i believe that's the silicon) but the down is just silence. and it works in bypass. I touched up all the solder points on my transistors, and in the switch. Not sure if...

Hey friends, I’m building my 2nd cataclysm delay (first one is great) however when I turn this one on there’s a crazy oscillating-esque squeal. You can still faintly hear the delays under it, but it is super noisy. I checked all my resistor values, checked my solder points (I think I got them...

Hello, I have an Amentum Boost that works and sounds killer on bass when boosted. I was trying to add a master volume to get that boosted signal tone but still be able to regulate volume to match hen in bypass. I added an A100 pot going out from the footswitch to the tip of the output jack...

I just wrapped up a kliche mini, and it sounds good in bypass. When I click it on the volume and tone work but there is no gain. When I roll it off it kills the signal, but there’s no drive when you push it. Any idea where the problem may be?

Hey, so I’m working on my 2nd ADHD. For the 220uf caps I used 16 volts on my first one and it works great. But I accidentally ordered 25v for my current build. Just curious what difference this would make. I noticed they are larger than the 16v in my first. Still new to this and I figured I’d...

Hey, I'm sourcing some parts to do a Percolation Station, and C2 calls for a 50n cap. I'm having a difficult time find one on my usual sites. Would there be any major issues using a 47nf or 56nf instead? thanks in advance!

Hello all, this is my first non-BYOC build so appologies for it being a little sloppy. The pedal works in bypass mode, but when it turns on the LED won't light up and there's no sound. any help would be appreciated. thanks!