Recent content by caspercody

  1. C

    Adding volume to CE2

    I am sorry, I forgot I wired both the dry and wet output to pins 1 and 3 of the blend. After reading your comments I then realized this. I went back and hooked up the wet to the correct out put and then I was able to get unity gain. Quick story, I received a PCB for the Rockman X100 (old...
  2. C

    Adding volume to CE2

    Hello I made a CE2 using the attached schematic. I used a different BBD clock and got everything working, but my output volume is less when engaged then when bypassed. I was thing if I add a POT (I used 50k) in series with R11, I would be able to increase the volume. But it did not work. Is...
  3. C

    Rockman X100 Rev. 10 Schematic Release

    Cybercow I just completed a vero board layout I created for your switching one of four logic switching circuit with the upper purple box with the four diodes and circuit to the right. It does switch between all four, but the clean sounds sound a not so clean. Can you please let me know which...
  4. C

    Rockman X100 Rev. 10 Schematic Release

    Looking at the schematic then, would I still need the four diodes in the purple box and everything to the right? And the bottom schematic wiring would replace the wiring to the left of the four diodes in the purple box with no connection to Q1
  5. C

    Rockman X100 Rev. 10 Schematic Release

    Cybercow Thanks for the quick reply back. On your original X100 mode switch you showing bottom right corner how to hook up the Rockman original SW101 mode switching to your circuit, but I do not see how to connect your new one-of-four switching schematic. Do the two different one-of-four...
  6. C

    Rockman X100 Rev. 10 Schematic Release

    Cybercow Do you sell the PCB board for the X100 mode switching
  7. C

    Rockman X100 Rev. 10 Schematic Release

    Cminiutti I do have a copy of the original schematic and information for the X100 and Soloist. But it is a PDF and I cannot attach to this forum. I did convert and attach pages 2, and 3 which are the schematic. There are 42 pages total for the PDF
  8. C

    Furman PQ-3 DIY

    Hello I created a veroboard and made the Furman PQ3, and it worked on the first time powering up. Honestly I was shocked as this is a big board and lots of wiring. I attached an image of the schematic I used. The input goes directly to pin 3 of the Gain pot, and exactly as shown on the...
  9. C

    Walrus Eras

    Any update on a schematic and PCB for this pedal?
  10. C

    Rockman X100 Rev. 10 Schematic Release

    Cybercow I was just wondering if you finished the X100 FV1 patches? I just finished my Binaura build and remembered your post about having patches. Are your patches for the chorus or delay, or both
  11. C

    BINAURA STEREO FV-1 PATCHES

    I was able to get my EEPROM programmed using my Arduino, but it only is able to load one program. It is a INO file from a project on DIYSTOMPBOXES, Tonewood amp. The author wrote the INO so one could copy and paste into Arduino and easily burn to a EEPROM. But this was for just the one program...
  12. C

    BINAURA STEREO FV-1 PATCHES

    I ordered the EZP2023. Looks to be a newer version.
  13. C

    BINAURA STEREO FV-1 PATCHES

    Hello What do you use to burn your EEPROM chips? I did this years ago using an Arduino UNO board and a Vero board from Madbean pedals. I still have this setup, but I do not remember the steps to convert the file to be burned using the Arduino. I am guessing the easiest way to burn the SpinASM...
  14. C

    Intelligent Relay Bypass Module document

    Thanks!!!!!!!!!!!!!!!!!!
  15. C

    Intelligent Relay Bypass Module document

    Hello I have the board pictured below, but when i click the Download Build Documentation on the link it gives me the documentation for a different board. The documentation that it provides is for the Intelligent Relay Bypass Module but it is for the second picture I post below. Does anyone...
See more
Back
Top