Breadboarding Practices

T

The Grand Wazoo

Active member
Greetings, all. While I’m only 10 pedals in with my diy journey, I’ve been wanting to start breadboarding so I can play out my “what if’s”. What I want to know is, do you save your breadboards with prototype circuits? Or do you just pull all the components and move on to the next thing?

What is the breadboarding platform you are using? PedalPCB Protoboard? Coppersound DIY? Other? If using one of these integrated platforms and you save your designs/mods, do you buy an entire new instance of that platform or do you remove the breadboards and replace them?
 
The Grand Wazoo said:
do you save your breadboards with prototype circuits?
Click to expand...
only until I've finished the actual final build of the pedal that the breadboard build/circuit inspired in the first place.

The Grand Wazoo said:
Or do you just pull all the components and move on to the next thing?
Click to expand...
yep, pretty much. i will rebag the 'used' components to reuse again and again specifically for breadboard builds.

The Grand Wazoo said:
What is the breadboarding platform you are using?
Click to expand...
this one.

The Grand Wazoo said:
PedalPCB Protoboard?
Click to expand...
The mini version was my first breadboard rig and it's great for small circuits.

The Grand Wazoo said:
Coppersound DIY? Other? If using one of these integrated platforms and you save your designs/mods, do you buy an entire new instance of that platform or do you remove the breadboards and replace them?
Click to expand...
if i want more breadboards I buy busboard brand breadboards from mouser.
dont even bother with cheap ones, they are heckin awful compared.

a lot of these breadboard "platforms" are all pretty much offering the same thing with different layouts.
i guess pick whatever looks good and comfortable for your workflow, or DIY your own
 
Last edited:
owlexifry said:
only until I've finished the actual final build of the pedal that the breadboard build/circuit inspired in the first place.


yep, pretty much. i will rebag the 'used' components to reuse again and again specifically for breadboard builds.


this one.


This was my first breadbaord rig and it's great for small circuits.


if i want more breadboards I buy busboard brand breadboards from mouser.
dont even bother with cheap ones, they are heckin awful compared.

imo, a lot of these breadboard "platforms" have a lot of superfluous shit i'd never use for analog guitar pedal circuits. hobbyist retailers gotta have their selling points i guess.
you could DIY your own or just pick whatever looks good and comfortable for your workflow. heardle game
Click to expand...
When you’re reusing the components from a finished breadboard, do you have any particular method for documenting the final circuit and the changes you made along the way? I’m wondering if you keep a schematic/notes somewhere so you can recreate a mod later without having to rebuild the whole thing from memory.
 
jeleta said:
When you’re reusing the components from a finished breadboard, do you have any particular method for documenting the final circuit and the changes you made along the way? I’m wondering if you keep a schematic/notes somewhere
Click to expand...
i'll either make a post about it somewhere here, that i can then refer back to later,
or
ill just write some notes in a little booklet/pad.

photographs of breadboard builds have also proven to be quite valuable to me during moments of 'wtf is going on here' / 'what did i do?'

jeleta said:
recreate a mod later without having to rebuild the whole thing from memory.
Click to expand...
usually this is possible, but often ill find when it comes to doing an actual build, ill have new ideas i wanna try, which ultimately means breadboarding the circuit again, to verify these ideas (because peace of mind and removing all doubt is quite valuable to me)
 
I was inspired by Owlexifry, but decided to do breadboarding in the most expensive way I could.
I have the Pedalpcb auditorium, which I have a little attachment to to clip straight onto pedalpcb projects.

clippy thing

And I use the pedalpcb protoboard, with busboard branded breadboards(mouser) and some basic wiring from Tayda
Tayda part numbers A-3480, A-3478, A-3482, A-6024

I usually start by buying the PCB first, because I am a fool. I then accumulate all the parts, build it on the breadboard (often two or three times, until I work out which connection I missed) with any planned mods, and then pull all the parts and solder them directly to the PCB. If i put it away I put all parts back into their pink baggies.

When I have something constructed on the breadboard I often setup a basic ditto looper pedal running a riff into a tonex one for headphones so I can fiddle with both hands.
 
zeropluszero said:
build it on the breadboard (often two or three times, until I work out which connection I missed) with any planned mods, and then pull all the parts and solder them directly to the PCB.
Click to expand...
hell yeah. this is the way. i should probably do it this way too, but i’m deranged and insist on using virgin components for final builds
 
The Grand Wazoo said:
Found it. Thank you!
Click to expand...
Get some DuPont cables for connecting. You can trim down the plastic and use one for power IO on most boards as well.
If you use 2, one 4 pole one 6 pole, connected with DuPont female to female or a 4 wire 2.54mm JST, you can pre test your 3pdt switch as well.
Not totally necessary (I've only ever had one bad switch and it was my fault) but it's nice to have. It also makes it easier to cable because you just need to run your in and out and don't have to think about the rest. Tests your LED too which is nice because I've definitely inverted led polarity more than once.(on ppcb boards that have the LED between the power input, you obviously can't populate the LED and use a clamp to connect power)
The pogo pins are fairly fragile. Careful as they can get stuck in the through holes some times so pay attention when disengaging them. This isn't as big of a deal on ppcb boards, but can be an issue on others that have slightly larger through hole diameter.
 
You must log in or register to reply here.
Back
Top