Search results

I'd be all about this. EasyEDA isn't the only PCB software I'd ever use, but for making boards to be fully/partially assembled by JLC, I'd rather confirm as many parts as possible in the design phase. Alas, so many sketchy user-contributed parts! I wonder if there's a way to make a...

Drag guides from the rulers to mark the center (Illustrator will indicate the center and lightly snap to it). Then, drag the top left corner area of the rulers to the center point. It will snap too. You can check it by putting guides on the sides of the box and making sure their distance from...

Whatever this is. Actually, it's 300mS. So, 300mS is enough for me.

Goes to show, you can't trust the Texans. Kidding!

Eagle is being discontinued in June 2026. IMHO the only reason to use it is if you're already settled into its paradigms and two years is a pretty long time. Plus, there are still a lot of open/shared projects that are in Eagle. Otherwise, KiCAD is the better choice of those two, to invest in...

I like it in a Rat. Its slew rate is listed as 0.4 V/us, compared to the LM308's 0.3 V/us. I can't hear the difference between it and a 308, but an OP07 is probably as good a choice if a 308 isn't available. I have a 307 in a DOD250 and am really getting along with it. But that could be as much...

Small Bear has some silicon "dot" transistors sorted by gain. I got some of the low-gain ones for Sziklai pairs and they tested in the advertised range on the TC-1. Searching for "silicon dots" should turn them up.

They should be in the linked Dropbox folder in the first post of this thread (you'll need to login): https://www.madbeanpedals.com/forum/index.php?topic=17740.0

Only one I know of is at Fuzzdog: https://shop.pedalparts.co.uk/product/ogpcb

I've gotten some good Ge transistors from Ebay lots... amid a majority of low gain and/or leaky ones. It's nice to have a stash and the low-gain ones can be put to some use, but I'd look for tested single transistors, or sets. For example, these always seemed like a good deal...

I use a version of the T12 for most soldering work at home. Its display is simpler but AFAIK the tip control is the same, or probably a little more sophisticated in newer models. I relegated the Hakko FX888d to my office at work because the T12 is easier to use and I can stash stuff on top of...

It's an important subject, and that makes it important to support his claim that Chinese counterfeit goods equal organized crime. He doesn't. Absent some evidence that Chinese counterfeit guitars are connected to organized crime in the sense that he uses the term, it isn't the case that buying a...

Brian Wampler's article on D+ mods is informative about the circuit in general. GPCB's Emexar build doc (found on this page) has a table with values/omissions for both circuits. https://www.premierguitar.com/gear/mxr-distortion-plus-mods...

I put a Madbean Weener Wah in a Crybaby shell (reused the stock inductor) and it's rocking now. I used Jerry Cantrell specs, at least according to the internet. The Weener documentation has info on how to use classic specs and lots of options, befitting its simplicity. Honestly it didn't really...

If you have control over the board layout, it works to use screw terminals that have 2.54mm spacing.

Or in a Darlington pair with another low gain PNP, or in a Sziklai pair with a low gain NPN. IME, gonna just stash this one away and get around to doing that sometime I guess.

Some possibilities here, including some coin cell holders: https://www.adafruit.com/category/889 Also a couple LiPos in series would get close to 8v, and they're easy to charge with the USB chargers on that page. I always just use their JST connectors rather than trying to cut the wires...

I'd be down for one of each volume-only board. I have a bunch of ATTiny85s and a couple OG Digispark boards that aren't currently in use. I have a bunch of travel coming up so I can wait until after the holidays. Just let me know what the cost is. Thanks for all the dev work!

Have fun and good luck! I've had good results by nipping the board apart to get the the transistors, to ideally avoid heating them more than necessary. If you can isolate each lead, you can just flick the remaining stuff off with one swipe of the iron. The board can crack in random & violent...

I've salvaged transistors from a few radios. While there have been a few high leakage ones, the majority are under 200. But a lot are low gain. Here's a rough survey by gain bucket (tested with TC1): 200+: 5 (4 are >300 leakage) 100s: 5 (a couple are leaky) 90s: 1 80s: 1 70s: 3 60s: 2 50s: 6...