Search results

Meanwhile, I'll begin to build the board of the Big Muff, I hope within this week. :)

I replaced the Blend pot of the ROG Splitter Blend with a pan pot like this: But the two outputs are not joint, but each goes into an op-amp gain stage (yes, they boost a little bit to pair the volume of the two loops, just in case) and then they are joint in the output. To make pass just one...

Thank you for your help and courtesy 🙂 First point: By blend I don’t mean a classic mix pot where CCW = 100% fuzz / 0% clean, noon = 50/50, CW = 0% fuzz / 100% clean. What I want instead is to keep the fuzz always at 100%, and use a pot to add the clean signal from 0% to 100%. I already...

Inverting the phase was the thing I didn't want to do, I forgot it. Thanks, but these layouts (I like vero!) are blend. :D I don't want to blend fuzz and clean, there's no much sense to me turn the fuzz into clean. I want just add the clean in parallel, and I thought to have a slightly boosted...

I'm sure Paralyzer is great. Actually, I built a modified ROG Splitter Blend with that same kind of blend, and my version has the blend mode and a mode with a fix side and the fade in or out the other side. :) But now I was searching a way to get the clean add with just a mini board a a few of...

Ok, I think I got what do you mean. Even if the connection of the Mini Blend Jfet has the input from the jack in the buffer/blend and in the main circuit, so there's a "passive split". I seen the Paralyzer, but I want to try to make something easier, and I drawn this, hoping that will work...

I thought it was like that, but after a gain/clipping stage it isn't properly a clean signal.

I'm afraid I didn't understand the connections you're suggesting. A schematic would be very helpful, please. And thank you.

But I prefer don't use a blend control, even the one you linked me I know works very fine. I'm reading that thread, but I have to see better if there's something about just a "clean adding". I prefer not to modify the basic Big Muff schematic, but to use switches so I can change it and switch...

Well, I heard all that low end make is fine on the bass, but actually that's not the point. I mean, I built a few of two or three fuzz pedals good for bass, but no pedal at all with blend or clean pot, so I thought why not make it on this one? Is a way to use this drilled box I have. Indeed the...

Thanks! There's a resistor after the Clean pot, but where exactly should I place the mixing resistor from the Volume 2 of the Fuzz? And you see a buffer/boost after the mixing, I'll see if I have to do it. Maybe I'd need more parts and a 3DPT toggle switch, but I guess it could be still ok...

Hello, I drilled the enclosure incorrectly for a different circuit, so now I want to use it for a Big Muff 2. This enclosure has four potentiometer holes, one toggle switch hole, and one SPDT slide switch hole. I want to use all of them, of course. I can add another SPDT slide switch if needed...

Thank you. Too bad, I can't download the document! :D

I'ts a very nice group of schematics! :) There's just a thing I can't understand. In the distortion section, a pair of caps ends in white triangle that is not ground nor voltage reference (Mid supply, in the schematic). So what?

Thank you. I saved the schematic, even if I guess that is the stock, apart the trimmer. Could you remember me what the trimpot do? Stock resistor value is 47k. I'm still searching some schematic that includes a decay control and see where I can place it in this schematic.

I didn't considering to run the tremolo in parallel. I was thinking to put it in front of the reverb. Actually, in this project I was thinking about the Jordan Vico Vibe, that I built it in a pedal a few of months ago, so I know it, and I like it enough. The only difference is that I will have...

Thank you, it looks fine. I'll search something like that, too.

Excuse me, what do you mean with "adapter"? A new PSU? I did it immediately, after the wire broken. But seen the problem is just the cable, and this PSU is always been a very good silent one, I would like to repair it. :)

I'm sorry for my delay. I like this, if it was male. But I can't find it, and I have the idea it costs a little too much. I could even solder the wires and... done! Meanwhile, I'll try to invent something to solve it a bit better.

The Spaceman Orion/Hooke seems ok. I'm not sure it has the same presence and all the "wet" of the Surfybear. Anyway, I would like something more similar to the Surfybear, and we have the basic schematic. I could even try to drawn a layout by myself. But I'd like to consider some mods, too. Those...