Search results

The first 220uf is before the charge pump so can be 16v or 25v

I have 50v 10uf but not higher voltage 220uf in my stock. Can I use 330uf or 120uf? The Aion Ares uses 100uf before the charge pump and no 220uf at the back. Only 2x 1n5827 with 2x 10uf

I also tried changing the charge pump from 1044 to 7660s and it didn’t change the behavior. I will order some higher than 25v elco caps to see if that changes something. It seems not related to the transistor as I swapped these with no change to the behavior. Another thing I was thinking is...

Never seen this before with any builds.

It doesn’t, it’s not related to grounding. With my hand I meant covering it over the open back (without cover). When the cover is on it the hand has no influence. It seems that any material that reflects or bounces back is picked up? But thanks for thinking with me.

It's even stranger that this noise isn't occuring when the pedal is powered with 12v. I can place the lid at the switch side 1/3 and at the top 1/3 and no noise occurs. Only over the elco caps and 2n5457 area does it increase the noise. And even my hand position over it without closing the area...

BTW, running the 25v elco caps on 27.3v with a 12v PS eventually will destroy them right? They seem to be doing fine. :)

I received new ICL7660SCPAZ and 2n5457 today. The 2n5457 were all marked with CEN in front (Central?) and had different gain levels. I tried all combinations but none resolved the issue with the noise. On 12v it works perfect on 9v it doesn't. I think replacing 4 of the 5 elco caps to higher...

Yes, I used the zener diode. I swapped the 2n5457 with the one I had. Receiving some others today hopefully. Aion uses other transistors. I could try an alternative to the 2n5457 as well. Any other transistors I can try?

It's still frustrating that there's no explanation why this occurs? It can't be a build error if it works at 12v. EDIT: you can imagine that I'm close to just buying a EP-PRE or Secret preamp.

Ok, I took the 9v battery out of my multimeter and tried it. It doesn't make any difference to a 9v PS. I also increased the bias voltage to above 17v on 9v which didn't make a difference either. So this isn't related to power I guess? It's concentrated aournd the elco caps and the transistor...

I haven't tried with a 9v battery yet. I normally use an external battery to 9v cable but all my 9v batteries are dead so I have to order some. Which type of batteries do you use for pedals? In general it's good to know if the pedal works better with a 9v battery but in practice this is still...

The voltage I measure using 12v is 27.3v and at the 2n5457 it's 17.0v. The strange thing is that using 9v the voltage at the 2n5457 is 16.8v. So that's very close already and strange that the pedal behaves so different. So is the 27.3v or the 17v passed through to the elco caps? I read this...

Ok, I had a little fight with the pedal removing the 2n5457 but ended up getting it out and replacing it with a socket. So I replaced the 2n5457 and the same issue at 9v was still there. So I tried to connect a 12v out of my Eventide Powerfactor 2 and the noise was gone! Connecting a 9v from...

I bought 3 new ones from a trustworthy source in the Netherlands which probably arrive tomorrow. It might be that the CEN one (which I have a spare one off as well) is not performing correctly? I will see what happens if I replace it.

Musikding. I noticed I have 2 in my stack and ordered 3. I need to remove the current one first which is always a pain. I have one similar like yours (CEN) and the other one has an F at the top.

I had a 7660S in my stack but changing it didn't make a difference. I did notice that the voltage of the 7660S probably is lower because the output was reduced. Noise still occuring when placing the pedal on a flat surface without lid open side facing down or when placing the lid on it and even...

It’s quicker to order in the Netherlands. :)

I ordered an ICL7660S and a few other 2n5457. The build document mentions 25v minimum except for c100

In your demo the Clandestine doesn't introduce noise. I do hear what I would call a light crackle and some pedal noise (or PS noise?) coming from a different pedal or QC?