Recent content by MacGuffin_

  1. MacGuffin_

    Abyss Rate LED possible?

    Coming back, so this method makes a pretty LED but absolutely DESTROYS the tone. Going to try attaching it to the LED anode instead later and will report back
  2. MacGuffin_

    Bypass when on, mute when off

    That and figure out if it is "supposed to sound like that" lol. Seems like most settings do not much at all (for a guitar at least), but when you hit a sweet spot it sounds fantastic! Edit: Was my lazy rate LED mod, turns out attatching something to the thing that makes the tone is NOT a good...
  3. MacGuffin_

    Bypass when on, mute when off

    Tried that, ended up replacing the pot and it worked. Probably just unlucky (or managed to break it) She done, now to finish the 2nd one so I have something to sell to recoup cost lol
  4. MacGuffin_

    Bypass when on, mute when off

    Sorry, left lug looking at the bottom up (as if mounted in the box), should be lug 1?
  5. MacGuffin_

    Bypass when on, mute when off

    Built one, used my synth as input. It gets signal up to the A100k, left lug works fine, no signal out of the right or middle. and that is no signal from the lugs themselves, not the solder point. Just a bad pot?
  6. MacGuffin_

    Bypass when on, mute when off

  7. MacGuffin_

    Bypass when on, mute when off

    Yep, bypass works fine
  8. MacGuffin_

    Bypass when on, mute when off

    D2 works flawlessly, I do need to buy a audio probe...
  9. MacGuffin_

    Bypass when on, mute when off

    After probing around more, I have 4.5v up until the A100k pot. somewhere between the 56k resistor and the pot I lose all voltage
  10. MacGuffin_

    Bypass when on, mute when off

    I had the LED wired to the wrong pin at the start, so it looked reversed to me. I get bypass, but absolutely no signal when engaged (box closed up or not)
  11. MacGuffin_

    Bypass when on, mute when off

    074: 4.5 [ ] 4.5 4.5 [ ] 4.5 4.5 [ ] 4.5 9.0 [ ] 0.0 4.5 [ ] 4.5 4.5 [ ] 4.5 4.5 [ ] 4.5 072: 4.5 [ ] 9.0 4.5 [ ] 4.5 4.0 [ ] 4.5 0.0 [ ] 4.5
  12. MacGuffin_

    Bypass when on, mute when off

    I haven't built a test box yet, it's part of the next lot I do but don't have the money for more components atm
  13. MacGuffin_

    Bypass when on, mute when off

    I got no idea how to do that. It has continuity and that's as far as I went
  14. MacGuffin_

    Bypass when on, mute when off

    No dice, also tried shorting the board ground to the middle switch lug with nothing there either. Resistor on anode has worked fine for me so far, it's how the board is wired by default anyway. The 9v rail doesn't seem to actually attatch to anything if you don't give it supply, so I was...
  15. MacGuffin_

    Bypass when on, mute when off

    Saw a reply that doesn't appear here for some reason: The resistor on the 3PDT board goes to the anode of a 3PDT LED then to ground after the LED. Didn't want to connect it to the right CLR pad because IDK what voltage that thing is getting and didn't want to dirty the +9v rail
See more
Back
Top