This Week on the Breadboard: The Yankee ScrewDriver Deluxe Turbo

[Solder of Destiny]

3.4V might be close enough. Are you breadboarding or building a PCB? We can tweak R18 to dial-in the drain voltage.

Thanks. It's actually this stripboard layout I'm working from. I'll socket and test the 3.4 jfet when I get to that stage. I've measured all the N-channel jfets I have and that's still the closest I've got

 

[Chuck D. Bones]

If you have a breadboard, you can build just enough of the 1st stage to check the bias.

 

[Solder of Destiny]

If you have a breadboard, you can build just enough of the 1st stage to check the bias.

Hi again (and sorry again).

I had to raise R18 from 33k to 470k to get to a drain voltage of 5.5v on Q1. Does this seem outlandish? And is there a downside to ending up with this much higher value?

The other thing I'm struggling with is getting Q5-E up to your suggested 5.3v starting point. The highest I can get there with the trimmer is 4.1v.

 

[Chuck D. Bones]

Hi again (and sorry again).

I had to raise R18 from 33k to 470k to get to a drain voltage of 5.5v on Q1. Does this seem outlandish? And is there a downside to ending up with this much higher value?

No, 470K is fine. Even removing R18 is fine. No downside.

The other thing I'm struggling with is getting Q5-E up to your suggested 5.3v starting point. The highest I can get there with the trimmer is 4.1v.

This is not a troubleshooting thread, but let's see if we can solve this quickly. Did you sub any parts?
Measure these four voltages:
Q4-D, Q4-S, Q3-C, Q3-B

 

[Solder of Destiny]

No, 470K is fine. Even removing R18 is fine. No downside.


This is not a troubleshooting thread, but let's see if we can solve this quickly. Did you sub any parts?
Measure these four voltages:
Q4-D, Q4-S, Q3-C, Q3-B

Thank you for your forbearance.

I built it exactly to the stripboard layout attached (with the exception of the germanium transistor and the aforementioned resistor change).

Q4 (BS170). D =8.94v, S - 4.8v
Q3 (104NU71). C = 3.4v, B = 0.65v

 

[Chuck D. Bones]

OK, I see what's going on. When you find Vero layouts on the internet, you use them at your own risk. I found one error on this board in about 30 sec. There may be others. I'll let you compare that layout to my schematic. If the error I found is the only one, then fixing your board will be easy.

 

[Solder of Destiny]

I hear you, but I'm not very experienced with schematics so I take my chances. Let me try to figure this out (it's going to take me a lot longer than 30 seconds).

 

[~Tu3ePh0x~78~]

is there is PCB for this? I would like to have two (spare in case I mess up the first one)

Also curious about the HFD inspired build Chuck designed IIRC

Thanks for the great work you contribute to DIY!!

Dean

 

[szukalski]

If you're not in USA then this is an option:

Screwdriver Deluxe Turbo

Sounds like Skreddy Screw Driver Deluxe with mods by Celestial Engineering Q2 can be any low noise Si transistor. Q1 can be any N-channel JFET with Vp around 3V or so. Not all J112s will have the right Vp. I actually use MMBF4393. Adjust R6 for 5.5V on Q1-D. Adjust trim to taste (start with 5.3V).

sheepylove.com