Trouble with Belton Brick BTDR-3 machine gun noises Ascension Reverb

hopburn

New member
I've been trying all day to sort this problem out and Icant get anywhere, so I hope one of you more experianced guys might be able to shed some light on my problem.

I have built a circuit from five cats pedals,


Schematic here


It make a constant machine gun noise that get loader or quieter when I turn the mix up and down. The other controls make virtually no difference to the sound.

I have checked all values of caps, resisters etc and all good, I have reflowed all solder that I can get to, the brick is now covering some of them.

I've got the following voltages

VREF - fluctuates between 4.3 to 4.37v
Brick pin 1 - 4.92v
L78L05 - U3 Pin1= 4.92v, Pin3 = 8.71v

Ive used a probe to test through the circuit to try and isolate the noise.

Its all clean up to the input of R7 and R5, outputs of each are noisy. On the brick pins 3, 5 & 6 are noisy.

The machine gun effect is a constant rate it doesnt change with any of the controls, or the switch.

The L78 is getting hot but has a constant output of 4.92v.

The supply voltage reads 9.02v

The only differences to the values on the schematic are the 25k pots are 22k and for R17 I had to use a 560R because I didnt have a 470R. I dont think either of these changes should cause any problems.

I visually checked the solder joints before I soldered the brick in place but I guess its possible that one of the joints under the brick could need reflowing, I'd really prefer to not have to remove the Brick, I cant see that being very easy.

If anyone has any clues as to what might be going on, or any suggestions on what I could try I'd really appreciate the advice.
 
Opamp 1
Pins 1,2, 5, 6, & 7: 4.32 to 4.38 fluctuates a bit
Pin 3: 3.75 to 3.81
Pin 4: 0
Pin 8: 8.68 to 8.71

Opamp 2
Pins 1: 4.08 to 4.43
Pin 2: 4.23 to 4.31
Pin 3, 5, 6, 7: 4.27 to 4.39
Pin 4: 0
Pin 8: 8.69 to 8.71

Brick
Pin1: 4.90 to 4.93
Pin2: 0
Pin3: 4.28 to 4.4
Pin4: 0
Pins5,6: 4.23 4.29
Pin7,8,9,10: 2.41 to 2.46

The L78 has 8.69 to 8.72 one side and 4.90 to 4.93 on the other

I'm not sure if the fluctuating voltage is the be expected or not?

Thanks for the help
 
Looks like the board may not have been cleaned of flux and solder spatters. That should be done before anything else because it could be a short from solder spatter. I would eliminate that as a possibility first.
 
Are you sure you have no bridges between the components and the back of a pot or maybe the switch? Looks real close on the length switch.
"Machinegun" sounds like a cap discharging

Do you have a audioprobe or can you cobble one together? That's really going to be your best tool for these types of things.
 
The voltages look OK to me. Agree with jwin, you got anything non-conducting between the pots and the back of the PCB? Looks like they could be touching C16/C17. If inside the case the pots will be grounded, too, so C16/17 could have contact to ground as well.
 
Definitely not the pots touching

PXL_20261114_212247423.jpg

I was quite careful to check the solder before I put the belton bridge on but if all the voltages look good then I think its looking like I may need to take the brick off and double check everything underneath.

I think that might have to be a job for tomorrow though.

Thanks for all the help, I appreciate you checking all the voltages etc micmac.
 
Never worked with bricks, but have you double checked all cap and resistor values? Are all gnd points on board making proper solder contact?

With my build history issues of weird noises/motorboating on FX circuits have usually been related to gnd issues or solder bridges.
 
I tried and failed to remove the brick, 10 solder joints are hard to remove enough solder to get it free, so I gently lifted the brick to access the solder joints underneath and they all look fine to me. I've gone over all solder joints and reflowed them, and I've checked all the component values, but its still the same.

I thought I might try bridging over the brick to see if it isolates the noise and when I make a connection from pin3, (input) to pin 5 or 6 (Out1 & 2), the machine gun noise vanishes and I get something close to a reverb, its a bit more like a delay with a slight shimmer in the background, but the controls do seem to effect the sound.

When conecting Pin 3 to 5 I get one loud repeat, when I connect 3 to 6 I get maybe 6 fading repeats like you would expect from a delay.

I dont know if that might shed any light on the problem?

One thing that has come up in searching what the problem might be is that a standard L78L05 voltage regulator can sometimes not be powerful enough, they are only 100mA, and this can cause the machine gun effect. The voltage on the L78 checks out ok and clearly with bridging the brick something is working but I might try replacing it anyway with a more powerful L78M05CV and see if that helps, I think the L78M05 is 0.5A so should easily be enough. Dont know if anyone has any thought on this?
 
Back
Top