Bad traces: PCB defect, soldering technique issue, or???

I'm running around 650 on my iron with it but I'm not convinced that's all that accurate(20+ yo 936 station). I can toss a couple feet in a PWE if ya want.
Gotcha, close enough! And thanks dude- if it’s really the bees knees I’ll think about just takin’ the plunge on a spool… hmm
 
Okay. Lemme find that affiliate link🤣
I'll toss you some tomorrow or, like, next Thursday. Sometime.
Deets still the same?
Ha! Ah dude ya don’t have to do that… but hey, if it fits in a stamped envelope I guess I don’t feel as guilty! :) Same deets! I really am curious… I do love Kester but cleaning those amber blobs ain’t great…
 
So I just bought a pound of Kester 24-6337-0027. This is 63/37, with the semi-corrosive rosin core. This is the same as what I was previously using too. It has the semi-corrosive rosin core, so definitely not no-clean. It is annoying to clean, it’s like pine tar, really gooey and sticky.

Before I bought it, I did a little research, and the impression I got is that the no-clean stuff is no-clean because the rosin flux is non-corrosive. While corrosive sounds bad, it’s actually beneficial in some cases, particularly if the work itself is already dirty, corroded, and/or oxidized. The corrosive effect of the flux helps clean away the mess, making for a better solder joint. I’m paraphrasing from memory, so that may not be quite precise. But the gist I got is that ideally the no-clean stuff should only be used on clean “virgin” work, and can be suboptimal for re-work.

I think populating a new PCB is probably the ideal case for the no-clean solder. But my thinking was, it’s not uncommon that I do re-work, so the corrosive should-clean stuff is more general.

But now I’m thinking I’ll just keep both on hand, because cleaning is a PITA.

Also: thoughts on Chip Quik vs Kester? I’ve gone with Kester because that seems to get parroted the most in solder recommendation discussions, but I’m open to others.
 
They also reduce acid traps in the corners of traces, when you have two meeting a hole at a 45 degree angle from each other, but I'm not sure it's relevant with modern PCB production.

Is there a setting to "auto teardrop?" Or you do you have to apply it each time?
I stopped using them for some reason, but after this conversation I'll likely go back to using them. I'm using KiCad, and I don't remember the exact particulars, but I remember it was pretty easy. Here's the v10 docs on Teardrops. It says, There are two ways to add teardrops to your design. You can add them in bulkusing the Edit Teardrops dialog, or you can add them to individual pads and vias in the respective properties of the pad or via. I know when I previously used them, I did it in bulk. so it was basically automatic.
 
I started playing with teardrops in EasyEDA and you can do it globally.

Select a trace > right click > add > teardrops

Brings up an option panel to adjust the teardrop settings.

Screenshot 2026-11-18 at 8.28.16 AM.png
 
as it turns out, snipping off the excess component lead(s) too close to the thru-hole can damage/sever continuity to the thru-hole.

learnt this the hard way one time.
You're not supposed to cut into the solder blob at all. Cut the terminal just above it.

Source: I took some legit soldering courses at an ISO9001-certified company back in the day.
 
Also: thoughts on Chip Quik vs Kester? I’ve gone with Kester because that seems to get parroted the most in solder recommendation discussions, but I’m open to others.
I consider them pretty comparable. I use Kester organic core solder which is similar to the ChipQuik listed earlier with water washable flux.

That being said I use ChipQuik solder paste exclusively, they're the best paste I've found.
 
Back
Top