Search results

The best method is paying someone else to do it. In the hassle of learning a free program, figuring out which material to use, how to print it, how to protect it, how to get it right…take that time well spent and just learn Affinity Designer. By the time you pay for the materials to print and...

Hey Mike, waking this back up. How exactly does one go about contacting Hugo? I’ve previously submitted a couple help tickets through my account to no avail, so I gave up, but I have another project I’d really like to try this on.

I'm pretty certain the text should all be facing to the right, just like it is for the other ones. I will confirm once I'm home from work and report back, hopefully as solved.

Actually, I think I see it. C12 (bottom right corner), which is part of the buffered bypass (if I'm reading the schematic correctly) appears to be the wrong way around.

Ok party people. Put together a total of three Informants all at the same time. One worked perfectly first fire up. The second, the LED would stay dimly lit in bypass. The third, buffered bypass is not working. Very fun. The LED issue on the second one, I worked out, but the third one is still...

Just one quick follow up, as I'm learning all of this on the fly and y'all are so very helpful. So the four outputs are all the 333mA max draw on current. So, I'm guessing that juicing it with the OneSpot is fine so long as I'm running low draw things like fuzzes, drives, etc., correct? Is it...

Makes sense. I will mark this as solved, and a great success in not damaging anything!

@giovanni & @jwin615 thank you both. I guess in theory, my thinking was “these are isolated outputs, should work just fine” but in actual practice, not so much. I had a feeling, and I knew going into it that it likely wouldn’t work, but figured I’d come to the actual smart people and see if I...

Ok, so I built one of the 4 Tap DC Isolators with the intention of using it as an off-board power supply for my “amp” setup, which is a UAFX Dream and Ox Stomp off-board. When I built the 4 Tap, I made sure to get the highest mA output I could find at Mouser, which was 330 mA, for each output...

There you are, good sir.

De-Soldering skills are good enough, lol. Yes, the jacks are easy 1:1. I plan to desolder at the board for the wiring and then go to a new switch that is softer click (SBP pro series). Where my confusion is lying is in the negative power side of things, plus what is going on with pads 2-3 on...

Hey there, fine folks. One of my buddies has asked me to rehouse his OCD 1.2, which I am happy to do, but I need some help with the wiring. I think. because the original power jack is hot glued into the enclosure, I’m not going to be able to get it out, so I’m going to need to replace it. We...

You and me both. I powered it with the battery and it was fine, so I thought that surely it was something dumb, and simply unboxing it, pressing here and there, moving this wire and that, reboxing it… that was the fix. It’s happened. I then used both Strymon wall supplies to power it, both...

Welp, apparently Strymon 9V power supplies are a no-go for this circuit (the single wall supplies, not the actual power supply bricks). It seemed to me that all the voltages were correct based on the schematic, I triple checked all resistor values, and then got home from work and just had a...

Voltages: Supply reading 8.81v at power jack, 8.56v at cathode of D100 (reverse polarity protection) TL082: Pin 1: 4.28v Pin 2: 4.28v Pin 3: 4.08v Pin 4: 0.00v Pin 5: 4.27v Pin 6: 4.28v Pin 7: 4.28v Pin 8: 8.57v Q1 (2N7000) 1 (S): 4.28v 2 (G): 4.28v 3 (D): 4.28v Q2 (2N7000) 1 (S): 4.28v...

Nope, no change. Didn’t get to do much troubleshooting tonight, so I’ll leave it for the morning before work. Steps thus far: - swapped power supply - removed from enclosure and re-tested - checked for bridges, gave another clean up wipe, brushed off board Tomorrow, I will try swapping out...

Ok, not exactly sure how to describe what’s going on, but basically my most recent build (newest iteration of ADHD w/ enhanced bypass board) is making a high pitched squealing noise. When pedal is in True Bypass mode, the noise only occurs when the pedal is engaged. When the pedal is in Buffered...

Got it, thank you! Found a couple of sites that have the component differences for at least V1.1-4, so that’s a start. Should be able to sort it out.

Also looking for ADHD docs. The values on the PCB are fine for most builds, but building a specific iteration for this particular board would be nice, especially since I’m looking to do multiple different versions and have a few boards sitting and waiting.

So I'm looking at adding a switch to go between symmetrical and asymmetrical clipping, specifically in the Cast Iron overdrive. I've attached a schematic of the clipping diodes, and just want to make sure I'm thinking about this right. First, if I want to just make it asymmetrical clipping, can...