Search results

  1. C

    Deadendfx Reflektor no delay signal

    Heyo! I recently built a DeadendFX Reflektor and am not having much luck with the delay signal. I can get bypass tone and a volume boost when I engage the pedal but the delay controls do not impact anything. I have swapped the tube, 2n3819, LM311, and the vactrol and still not getting much luck...
  2. C

    Lovetone flange clone DeadendFX

    Hello all! Looking for some help here. I have been trying to get my lovetone flange clone from Dead End FX to work, but I'm not having luck. The pedal turns on, LEDs light up, but when I try to bias via the instructions, it isn't doing anything. I did a reflow of the entire board, checked my...
  3. C

    2 in 1 AB wiring LED

    Hey all. I'm working on a 2 in 1 build with 2 Special ODs. For the LED wiring can I wire it up like the following? I want a blue bypass LED to show the pedal is on and then the red and green will be for their respective PCBs. Not sure if this works or not. I removed the SW wire from the right...
  4. C

    SOLVED Rangemaster and Muffin Fuzz 2-in-1 with Order switcher

    I recently finished up a Muffin Fuzz (Mask Us variant) and Rangemaster treble boost. I followed the 3PDT Order Switch Wiring and I'm getting bypass tone but when I engage the fuzz I get nothing and when I engage the boost I can hear a very faint signal with the knob all the way clockwise. Any...
  5. C

    Paragon Switch pop

    I recently finished a Paragon and noticed a popping noise from both sides of the pedal when I engage the switch. I understand that maybe this could be normal in KoT clones and in the KoT itself, but I was curious if there was any way to mitigate the popping. I reflowed my ground connections and...
  6. C

    Duo phase trimmer settings

    Hello! Just finished my duo phase. Everything is working well. Just curious what the ideal trimmer settings are. Should I have each side at noon? Roughly almost all the way? I guess I'm not sure what the ideal settings are or if there are some builder favorites that people have discovered. Thanks!
  7. C

    Special Overdrive ODS

    Hello! I have 2 special Overdrives built and was curious what the difference is in the ODS version that shins offers. I was looking to do a dumbloid twin style build but I noticed the second channel is normally ODS. Any tips on how to get that out of the special overdrive PCB? Thanks
  8. C

    SOLVED Abyss rate led stuck on

    Hello everyone, Just finished wiring up my abyss pedal. Sounded great and then I noticed the rate led stopped pulsing and is now stuck always lit up. I reflowed as many solder joints as I could and cleaned the board up too. Any ideas?
  9. C

    Dumbloid Twin build

    Hello all! I have two Special overdrives built but I am wondering how I can build them to mimic the shins dumbloid twin. I would like to have one footswitch turn the pedal on and then the other select between either ch1/ch2 as seen in the photo. Also, would a 1590bb be sufficient to make the...
  10. C

    Uberfuzz diode question

    Hello all how's it going! I have the uberfuzz pcb and I had a question about the OA90 diodes. I have some CV7130 diodes, would those work as a replacement? Thank you for the help
  11. C

    Nugget fuzz and buffer low volume

    Hello all I recently just finished building the nugget fuzz and c - buffer. I have low effect level when the switch is pressed. Also the LED seems to be always on. I checked for cold joints and possible bridging and didn't see anything. Any help is appreciated
  12. C

    Chicken head transistor

    Anyone know if a PNP transistor can be used if I flip the capacitor polarity? I have some OC44 transistors I want to use
  13. C

    Double tracker

    Has anyone built this yet? I want to know what it sounds like
Back
Top