Search results

@twebb6778 I get it, so if I test out without SW2 wired at all, I should be fine, right? If I understand the schematic right, then without the switch there's no connections for the high gain elements.

I've tested the height w/a pot in place and height should not be a problem. I am using a substitute transformer, and maybe it is smaller than the one that is recommended. Maybe that was a mistake, but folks here and at DIYSB seemed to think it will work. We will see! One vote for SHO after. Any...

This may not be the most exciting answer, but try the Joyo AC Tone pedal. You can get it used for less than $30. It's a sansamp clone of some sort (liverpool?) and it is designed to simulate an AC30. I don't know if it does that, but it does pretty much what you described. It's great for...

Hi, I am ready to add the pots to my Duocast PCB but I have some questions before I get started. Most important question--I'd like to test out the circuit before I wire the switches. That simplifies troubleshooting when something inevitably goes wrong. The problem is that I can't figure out...

@Ratimus I'm not familiar with discrete inductors. Are they cheaper than a wah inductor? Where did you get them and why are there 5 of them on the board?

It's working and sounds great, thanks everyone for your help! Gotta say, it is impressive how this pedal sounds considering the simplicity of the circuit!

OK, @PedalPCB I think your explanation has to be right. I'll install a new LED, put heat shrink on the legs and have the legs poke out of a strip of electrical tape that will serve to cover the bottom of the bezel. That should be enough, right?

Well I took out the LED Bezel, boxed it again, and it looks like it works fine even with the pots very tight. I am not sure the bezel was the problem, because I also replaced the electrical tape under the dg pot with paper and I re-soldered the pots. But I am thinking that the bezel is the most...

@PedalPCB Thanks for taking a look! You might see in the photo that I had put electrical tape under the dual gang pot, but that didn't prevent the problem. Also, looking at the schematic, I am not sure how shorting any of the pads under the dual gang would cause continuity between the + 9v and...

Here are more pictures (the forum won't let me upload them because the files are too large: https://drive.google.com/file/d/1Tp44jUplO2qsgUoYJUa93cqXRG5MkKtS/view?usp=sharing https://drive.google.com/file/d/1Lvkr7nv6ynaNoRBQ1pIIPEDfxqqKPAcC/view?usp=sharing...

It looks like this is the case at least for the top of the PCB. But I need to unbox to check the bottom side. Shot of the PCB top is at the following link: https://ucdavis.box.com/s/8at4bqz402yjfm6bfpj7lhuxj86cyx3u

I feel very stupid right now posting this, but I think it's time to get an outside perspective. I built the Son of Ben and it sounds spectacular. The problem is, when I boxed it and tightened up the nuts on the pots (not ridiculously tight, just a bit more than hand tightening) the sound and...

Sorry to revive a zombie thread but could you use a low gain Silicon NPN Transistor for the Red Rooster?

Thanks if you try the 003 please let us know how it works! I've had trouble finding inductance on the Xicon datasheets (maybe I'm looking in the wrong place?) and I have no idea what the inductor does in this circuit so it's hard for me to assess substitutes.

Hello, has anyone successfully used an alternative transformer for the conqueror supreme? I have a 42tm013 on order from Mouser but it wont ship till late november. Or is there a cheap inductor source? I'd like to avoid buying an expensive wah inductor if possible.

@benny_profane @PedalPCB do you have recommendations for a reliable, inexpensive source of unobtanium germanium transistors? Here's a couple I found on flea_bay...

OK, so seriously gain and other specs mentioned by the OP doesn't matter? It just has to be germanium??? How much is a reasonable price to spend? I've seen single OC71s going for $10. Does anyone have a better source? Even an eastern european seller that might do a multi pack for use in...

Yes I think I got this one on a recommendation from another internet group: 42TL218-RC Haven't tried it because I still need to get the germanium transistor. God this circuit is a pain for sourcing parts!

Just as an FYI, Mark Davis on the DIYSB FB group told me that this one will do the job: https://www.mouser.com/ProductDetail/Xicon/42TL218-RC?qs=%2Fha2pyFaduji1V3LuMrsD%252BiRY44PGJxR7cDph9r5agQ%3D&fbclid=IwAR2jTifOlVve39xc5f_S12X7_h8Yqv9StL6WWZDhkcNgen9H-qcbpyzZrjM I don't know much about what...