Search results

My other problem is now my board is basically finished, and I'm not buying 13 new enclosures with printing haha

Subbed mlcc, oh well.

Circulator phaser with most of Chucks mods. (1 to 12, skipped 13(probably could have done that one) and 14 only because I didn't order enough tantys) Is there anything nicer in the world than when you do a shitload of mods and it turns on turns on the first time?

Oh the attachment is there but not showing

UberKliche - Uber drive into Notakliche, with order switching. LEDs in D1/2, Bat41 in D3/4. Since theyre both overdrives I have no idea if one is feeding the other :lol:

Seems to be working. a load of squeal coming from the kliche if I max out the dials - my initial suspect is that the clipping doesnt like that - so...just dont do that. LEDs in D1/2, Bat41 in D3/4.

Ok, I haven't added them in yet, but this is my plan, should I connect the input jack ground to the boards, or maybe unnecessary?

For Mod 14 - I think the circled points for 1U are the anodes for using polarised tanty caps, is this correct? Naturally on my order I ordered 3 instead of 4, would I be better off substituting 1UF MLCC?

So this is what I think is right- With the Yellow being ground connections to the PCB from the jacks, Im not sure where S1 and R1 need to go for the notakliche, whether to the outer sides of the footswitch, or to the in-out at the top of the board.

Oh Do I make all 6 connections from the notakliche to the 3pdt then?

So I got my new enclosure in the mail after fucking up the drill template on the first one (that SUCKED) (Yes I'm aware of the input jack being very close to the switch & diodes) I'm looking to put the order switcher in place which I'm clear on the wiring for - Just need to know if the far left...

Yeh that's cool Robert, I'm less interested in this being a 'notaklon' pedal so much as it being a klon style with options built into the PCB.

Ah you both had the same idea haha. I guess good thing I socketed these, I can give those combos a try.

Could I put the bat41 into the LED sockets d3&4 and put germanium in the D1&2? I guess I'd sort of hoped to have that as my configuration. Probably should have just modded a regular kliche

Hey all, I'm hoping to finish off a notakliche feeding into an uberdrive this weekend, and just have a couple of questions. I'm looking to use bat41 for the main diodes at the bottom of the PCB - I can see the PCB is labeled with a stripe for what I assume is the cathode - although I also read...

Uberdrive about to be combined with notakliche, delegate rebuilding, circulator and abyss to round out my modulation options. Pod Express providing amps (I really want an FX loop) and HX one is primarily my Gate, tuner and any other shit I want. Scabbard, Angry Orange, Shika Fuzz, Acapulco lite...

Actually you know what is killing my aesthetics now? It's that I have two line 6 pedals, the shallow water that I stamped, the Hydra with its faceplate, and now about 8 other pedals with no descriptions at all. Hey Robert can you please make a faceplate for all pedals so I don't have to wonder...

Yeh i get what you mean. I am glad I'm getting tayda to drill these too, let them figure it out. (JK i have three painted, drilled enclosures here that dont fit what I needed them to because I fucked up the drill coordinates)

Hydra, with clock module. Not sure I needed the clock module in hindsight, but oh well. I did the dry mod and used an A10K for the mix, removed the pin on the pot, didn't like the result so soldered a wire in place. Might still change this to a B10K as the original design. Heads 3+4 seem to...

Magnetron, with momentary feedback, and trimpot to control that feedback. Feedback still uncontrollable. Kinda wish the wobble in this was a little stronger. Had to max out the gain trimmer too to get it as strong as I liked it. I also reversed the LEDs on the front so the rate is at the top...