Search results

Tube screamer module shared at PCBWay.com. https://www.pcbway.com/project/shareproject/Tube_Screamer_guitar_boost_board_for_embedding_in_a_combo_guitar_pedal_format_98ff98e0.html Interactive BOM https://paulamps.com/boms/Tube%20Screamer.html

When I order these, I get 10 boards for myself and usually don't need all 10, so I offer a few extras for $2 each plus shipping. If I don't have extras, I don't sell any and I will never stock up and sell them. I'm a (nearly) retired engineer sharing a hobby, which is why I put them on PCBWay...

I have some of them in hand if folks want but I'm posting them on PCBWay so anyone can order direct. Still have a bunch of modules to share, especially the primary module that has the amt legend series 2 clean, dirty and cabsim all on the main center board. I still have more pre-boost modules...

Have added a Plexi Drive pre-boost module at PCBWay.com. https://www.pcbway.com/project/shareproject/Plexi_Drive_pre_boost_module_for_embedding_into_a_combo_Guitar_pedal_93587a52.html Interactive BOM https://paulamps.com/boms/Plexi%20Drive.html

Have shared my simplified Prince of Tone pre-boost module at PCBWay.com https://www.pcbway.com/project/shareproject/Simplified_Prince_of_Tone_pre_boost_module_for_embedding_into_combo_guitar_pedal_173e99fe.html Interactive BOM https://paulamps.com/boms/PrinceOfTone.html

Have shared an alternative PCB for the Malachite Overdrive at PCBWay.com for embedding in a modular guitar pedal. https://www.pcbway.com/project/shareproject/Malachite_ovedrive_from_PedalPCB_com_in_modular_format_for_embedding_in_a_combo_87b07dfe.html Interactive BOM Link...

Have shared the mini-spark clean boost board at PCBWay.com. https://www.pcbway.com/project/shareproject/Small_guitar_Clean_Boost_circut_for_embedding_into_modular_Guitar_pedal_projects_ad69d8a1.html Interactive BOM: https://paulamps.com/boms/Spark%20Mini.html

In order to keep this thread full of all the modules shared, here's the thread about the alternative Pythagoras (Spin FV-1) module for embedding wet effects. https://forum.pedalpcb.com/threads/alternative-pcb-for-pythagoras-circuit-at-pcbway-com.22779/post-287707

I've shared the alternative Muzzle PCB at PCBWay.com. https://www.pcbway.com/project/shareproject/Keyed_Noise_Gate_for_Modular_Guitar_Pedal_Board_Using_4305Q16_U_Dynamics_Process_0be9e9ac.html It's almost identical to the Muzzle here at PedalPCB.com but I added voltage protection since the...

Had to make some tweaks to mine for signal levels. The clipping LED was on all the time, so signal was too hot into the FV-1. And then the signal out of the FV1 was hot and hard to only add a small amount of reverb. These changes might be needed for others. First get input signal adjusted to...

I have not shared the PCB modules (other than the FV-1) but I would be willing to do so if there is interest in this format for a combo. I've also now done a board that can make any of the 3 victory boost pedals (Bobby, Cetus and John on Pedal PCB) as a pre-boost module. The Victory Sheriff...

FYI... The board is 2.5x1.75". I squeezed the one above into a 1590G but it was very tight on the sides to fit the jacks and I had to cut a hole in the base plate for the jumpers and eeprom to stick through a bit (but it gives me access to them easily). This case is only 1" tall. If you leave...

Built one of these into a stand-alone, always-on reverb in a tiny case for my current pedal board. Also shown... My power amp with XLR out on the left and the all-in-one combo pedal on the right.

I screwed up the thread title. Meant to say "... at PCBWay.com" In order to embed reverb into a combo pedal, I've made a PCB in small format. My intent is to install an always-on reverb into a combo pedal and use trim pots to "set it and forget it." Here's one with alpha pots used for testing...

Have you resolved this? Mine is working. Have you tried grounding pin 13 of the FV-1 to run the internal programs and see if those work? With pin 13 grounded, you should get these three options: If you still get nothing, then maybe the fv-1 is not running, not properly soldered or dead. But, of...

I've gotten my FV1-Dev board working. But the software suggested by the wiki will not display correctly. It looks like this for me and I've tried all the compatibility mode crap to get it to display and it just won't. It works (after I found the right drivers online) but this bothers me too...

If grounding pin 13 allows the built-in programs to run, then the eeprom might be blank. Have folks gotten the fv1-dev board hooked up to the PC and tried reading the contents of the eeprom to see if it has a program in it?

Have you tried connecting to USB? It should show up in device manager if it's running but won't have a driver. The driver needed for windows is this: CH341PAR.EXE https://www.wch.cn/download/CH341PAR_EXE.html

And, yes 12V will work but will only reach about 1/4 of the rated power (assuming you want to use the same 12V for the power amp).

It has power-on delay but cannot detect power loss. It has a footswitch to enable/disable, so you are still expected to disable prior to power loss. The preamplifier has 2 jobs: one is to bring instrument level up to line level for the power amp. Second is a bit of EQ to add some sparkle, just...