Search results

Is this the correct regulator to use? From Tayda .....L78L33ACZ 78L33 + 3.3V Voltage Regulator IC i was'nt sure because of the extra letters at the end. They are already ordered and could be used for something else if they are wrong. thanks in advance to all.

Is this the correct crystal? the title is a bit misleading https://www.amazon.com/ABRACON-AB38T-32-768KHZ-CRYSTAL-32-768MHZ-12-5PF/dp/B00LQPAMJM/ref=sr_1_1?crid=2IZJA1IG8WMU3&keywords=ab38t-32.768khz+crystal&qid=1662913522&sprefix=ab38t-32.768khz+crystal%2Caps%2C195&sr=8-1

thot so thanks

can I sub 1n4148's for the 1n914's?

thank you what I wanted to hear

Would using 10.1K resistors instead of the 10k the arachnid calls for have any ill effect on the pedal. It's all I have at the moment.

Just asking … you think there’s better odds with e-bay over Amazon? Or just price wise it’s better?

just saw this yay or nay? I wouldnt know but seems cheap, no? hope the link works https://www.amazon.com/dp/B07BZBG7DY/ref=aod_recs_desktop_prsubs_2

i definitely would try a tonebender. I just assumed germanium was the awthentic way to go and the silicone ones were a psuedo fill in for whatever reason but I didnt really give it much thought . those 2 trannies are easy to get so its on the list now. And I gotta say I really did like what I...

Ive yet to build any fuzz face or tonebendr variants. Mainly due to most trannies from back then (this opinion based off all that I've read) either impossible to get or waaaay outta spec and lastly I find it hard to justify paying 12-?$ for a transistor that I'm unsure I'll like. I've found that...

thanks for the link . good reads.

So I am always ALWAYS looking for the newest(or oldest) best sounding ultra screaming od/disto Cause 1 I cannot afford any tube amp that I like Cause 2 Even if I could I couldn't crank it where I live So i got a Yamaha G-100 head with a decent reverb a pretty nice tremelo a super shitty...

Ok so reading about the arachnid and being clueless to EEPROM the arachnid is what? You swap out preprogrammed EEPROMs and get different effects ? If it’s as simple as that I’m in. Programming EEPROM s? Later. As long as I can get preprogrammed ones I’m assuming not every pre programmed one will...

Thank you that’s what I’m wanting. Simple clean delay.

Sorry I’ve been in limbo hell. I just ordered some 13700’s should be hear next day or two. Definitely got my fingers crossed. I have a couple other pedals with working ones but they’re old builds early in my build history and feel messing with either could create a problem (stupidly no sockets)...

Cool thank you . Which would you say has cleaner delay? The 4 switchable heads is intriguing but I have a couple of delays with degrading echos and looking for clean repeats

wondering if any one has built both and their likes and dislikes between the 2 thaank you

Thank you. I will give that a shot.

In the 2nd picture stating “there shouldn’t be a wire connected to pin 16”. It’s the angle of the picture that makes it look like a wire connected there. There isn’t. Still have not gotten this one to work properly having revisited this one several times over this year. I’m not one to give up...

Okay got it where it used to be I get signal in all toggle switch positions, bypass. In Vibrato mode there is no vibrato in phase mode phasing can be heard only by moving the sweep pot by hand and the phasing is audible but pretty subtle.