Search results

I was wondering the specs of the 2SD352 for the Trademark fuzz. I’m having trouble finding that exact transitor and wanted to try to get close.

I’m finishing up a Salesman but was wondering about the wiring. Obviously the in/out jacks get wired to the in/out and grounds at the top of the board. I wasn’t quite sure about the foot switches. Do those just get wired straight hole to hole? From the main board to the 3pdt board? I’m about 98%...

I’ve got a Soul Drive I’m about to start building. It’s got a test point on the board and I was curious what it was for. Obviously for testing but what would I be testing? Looking for a certain voltage? Also, there’s a 0 ohm resistor printed on the silk screen. Is this the correct value?

I was wondering if anyone had a wiring diagram for the Canis. I know on the board page there is a buffered 3pdt board listed with it but I didn’t order one (I’m not a smart man) and I’m at the wiring stage of building.

I just got the Canis board and C4 (at least from the image on the board page) is marked out. It looks like it was originally marked as 100n but now I’m not sure what it is supposed to be. Anyone know off hand?

I’m back with another question about footswitch wiring. Lol. This time I’m building a Double Tap. Is this wiring the same as the Hotlanta? I’ve been excited about this build so I couldn’t wait for build docs to come out. Lol. Any help would be greatly appreciated!

Hi everyone! I’m almost finished with the Dielectric boost but I’m not completely sure how to wire up the foot switches. I know one is just the normal 3pdt wiring, it’s the other switch that I’m not as sure about. Anyone know how this one is wired up? I looked at other 2 switch builds but there...

I’m not sure if this is the right place to ask but, are the InfiniDrive boards going to be coming back? I’ve been checking them for a long time now and I haven’t seen them in stock since I found PPCB.

I’ve got the Cetus preamp and the rest of the line and while looking for the diodes I could only find the 2v7 in 1/2 watt size. Is this too small for the build?

I’m building a Proposition and don’t have any transistors within spec. I was maybe planning on bypassing and jumpering the transistor. My question would be when jumpering the transistor, where do I put the jumper wire? Through the D to G? D to S? S to G? Or do I try and jump from each hole?

I know that there are several transistors that can sub in for the 2N5210 but I was curious if there were some that would work better that others in the Topographer circuit. I’ve got 5089, 549C, 550C and MPSA18s.

I’ve got a Kinetic Fuzz that I’m building. Going through it shows a 470n capacitor in C2. It looks like it’s a electrolytic capacitor. I’m just curious if that might be a misprint? I’m guessing not since it’s in the docs, schematic and on the board. Anyone know about this? If it is 470n would...

Hey everyone, I’m building a Fet City Drive. The schematic and build docs call for a 22k in R16 but the silk screen shows a 1k. I’m leaning towards going with the docs and schematic but just wanted to hear other’s thoughts about it.

Hi everyone, I’m building a Double G version of the Muffin Fuzz. The build docs show to populate R24 and 25 but for the life of me I can not find them on the board. There are asterisks on the build docs but there aren’t any notes that I can find to explain. Does anyone know where these go?

I know it’s still coming but, is there a wiring diagram and drill template for the Acetylene available? Or a wiring diagram from another project that will work for the Acetylene? I hate to be a pain.

Building a Colorsound Powerboost and the build docs have a 470n MLCC in C18. Would a box film capacitor work as well (or at all) in its place? Schematic included for reference

What would be a good substitute for a 2N5457 in a Bluesbreaker circuit? I’ve included the schematic if that’ll help.

Would J112 be a decent substitute for J113? I’m building an Acetylene and could have sworn I had 113s but I can’t seem to find them.

I finished my Electrovibe but I get no effect when engaged. Dry signal passes and the bulb flashes. When I flip the switch to vibrato it completely cuts out. I went through and reflowed every joint on the board and 3pdt boards. Wasn’t sure if anyone might have a direction to point me in to...

Hi all! I’m set to build an Antithesis but was wondering what specs would work best for Q1? I’ve got several transistors that should work but was just wondering what would be recommend to get the best results.