Recent content by Elijah-Baley

  1. Elijah-Baley

    Jack Orman's Pickup Simulator / Anti-Buffer...

    Ok, the switch (and maybe the also the pot, I guess?) changes the impedance. I still have to try it with a Fuzz Face, maybe I can hear some difference in the sound. I assume that changes something in the sound, too. Else, what does it mean? I hope to clear it out this week. :)
  2. Elijah-Baley

    Jack Orman's Pickup Simulator / Anti-Buffer...

    Hello. Without open a new thread I want to ask here something about this Jack Orman project. I built a version with the updated schematic, the one with Volume and Tone control, with no issue, and my built include even the early version. This: I testing it, without any other pedal. But switch...
  3. Elijah-Baley

    1590B & Top Jacks: It Can Be Done

    I did it, too, a few months ago. :) It wasn't easy at all, because a three pots line close the upper side. But I did it.
  4. Elijah-Baley

    That4305 issues

    I received the third 4305 module, and this time seemed work. I'm not sure if the pedal worked so fine like the first Muzzle with 4301 chip. I tested it with different gear, but I wasn't so impressed like with the first pedal.
  5. Elijah-Baley

    Tone bender mk1.5

    Let see the exact schematic of this, please. And your transistors are...
  6. Elijah-Baley

    volume attenuator recommendation

    I guess a potentiometer in the loop effect is an easy solution without mod your amp.
  7. Elijah-Baley

    Stone Age Distortion What's with R8 and R9?

    I noticed that weirdness, too, just yesterday.
  8. Elijah-Baley

    Boss DS-1 (MIJ) build - transistor boost config vs selecting transistors?

    What's your schematic? About the thicker sound (A LOT?) and removing the JFET switching, I see some adjustment of the coupling cap, to keep the same low end. Maybe that's the thing.
  9. Elijah-Baley

    SOLVED Aion DZ-4 whistle/oscillation

    You could try shielded wire, for input and output. I can't say if it will solve that problem, but you could try. I heard about oscillation issue with this pedal a lot of time, not this PCB in particular, but maybe PedalPCB, too, and also veroboard and protoboard. You could even try to use a...
  10. Elijah-Baley

    THAT4301 Substitute?

    I got issue with two of them, when I replace the original THAT4301. In a Muzzle PCB. :(
  11. Elijah-Baley

    Try pedals by home (kind of like Thomann)

    My friend is better equipped than me: sound-card/interface, amp modeling software... I have just my pc with the input mic. I used to connect my pedal through the old Behringer V-Amp (kind of old red Line 6 POD), to make the amp and cabinet emulator. I don't know if I can make the thing. In case...
  12. Elijah-Baley

    Try pedals by home (kind of like Thomann)

    Hello, a friend of mine asked to me to try my pedals from his home. (A bit like Thomann). He lives a bit far away from my home and he can't come to me every time. Does someone know a method how he can play his guitar at home with the pedals in my home through our computers? It's ok if I have to...
  13. Elijah-Baley

    Ionizer2 Fuzz

    I just built on stripboard the version without the Oscillation control in an 1590A box. After I put the everything into the box, I got a loud oscillation noise that change pitch turning the Intensity control, but even the volume of the guitar. It was causes by the tip of the input plug, it...
  14. Elijah-Baley

    Jack Orman's Pickup Simulator / Anti-Buffer...

    Thanks, Feral Filine. TY-250P Datasheet https://eu.mouser.com/datasheet/2/410/TY_250P-1892894.pdf
  15. Elijah-Baley

    Jack Orman's Pickup Simulator / Anti-Buffer...

    If I remember well, the inductance of the part that looks like resistors and capacitors are too small. I know just this kind of transformer have the characteristic that can "emulate" pickup. I include this, too. It can help to go close to the pickups specific. Generically, the inductance is a...
Back
Top