xefned
Latest activity Postings About
-
-
Same. Especially since I frequently design enclosures before I even have the PCB on hand -
xefned replied to the thread Corduroy question (trim pots).I have both revisions. It appears that no parts changed since the previous revision.
-
xefned replied to the thread The Thing (Dynamorph from DeadEndFX) LEDs are always lit (and not in a good way.).Any value in the DNL spot kills the envelope effect for me, even low values under 100Ω. I swapped the fake 2k rate pot with an actual...
-
xefned reacted to Diynot's post in the thread The Thing (Dynamorph from DeadEndFX) LEDs are always lit (and not in a good way.) with
Like.
I have an Xvive vtl5c9 in mine, but with a Cordyceps board on its way, I may harvest that and try the NSL-32SR3. Mostly because I’m... -
xefned replied to the thread The Thing (Dynamorph from DeadEndFX) LEDs are always lit (and not in a good way.).That's why it's tempting me. Any sign that says "do not touch" makes me want to touch it. I covered it over with a white sticker so I...
-
xefned reacted to Fuzzonaut's post in the thread The Thing (Dynamorph from DeadEndFX) LEDs are always lit (and not in a good way.) with Haha.
DNL=do not load, remember? ;)
-
xefned replied to the thread The Thing (Dynamorph from DeadEndFX) LEDs are always lit (and not in a good way.).I had a leftover VTL5C3 desoldered from the Meatsphere, so I just used that from my junk box. BTW, I had a perfectly working Meatsphere...
-
xefned replied to the thread The Thing (Dynamorph from DeadEndFX) LEDs are always lit (and not in a good way.).Cool. Thanks for the tip on the Prunes and Custard. Definitely has the same harmonic characteristic, but in a smaller box with simpler...
-
xefned reacted to DGWVI's post in the thread The Thing (Dynamorph from DeadEndFX) LEDs are always lit (and not in a good way.) with Like.
Perhaps I'll pull mine out and tinker more. It gets most of the sounds I've seen in Andy's demo, so I'm guessing it's not too far off...
-
xefned reacted to DGWVI's post in the thread The Thing (Dynamorph from DeadEndFX) LEDs are always lit (and not in a good way.) with Like.
I've got a similar issue with mine- the LEDs stay lit no matter what. I am able to bias as low as 6.39, and no further. I don't recall...
-
xefned reacted to Diynot's post in the thread The Thing (Dynamorph from DeadEndFX) LEDs are always lit (and not in a good way.) with Like.
@DGWVI that was me. But yeah, same issue, but to be honest mine sounds ab like the demos. I spent a bunch of time troubleshooting and...
-
xefned replied to the thread The Thing (Dynamorph from DeadEndFX) LEDs are always lit (and not in a good way.).Also, you gotta wonder what that DNL resistor was for. Looks like some voltage divider in the negative feedback loop of one-half of the...
-
-
xefned replied to the thread The Thing (Dynamorph from DeadEndFX) LEDs are always lit (and not in a good way.).After more dicking with the trimpot, there's a sweet spot where the LEDs pulse in time with your picking, but it's at a lower voltage...
-
xefned replied to the thread The Thing (Dynamorph from DeadEndFX) LEDs are always lit (and not in a good way.).Actually, yeah. It's noisy, and a bit of a one-trick pony. But at the right setting, it's morphing nicely and spitting out all kinds of...
-
xefned posted the thread The Thing (Dynamorph from DeadEndFX) LEDs are always lit (and not in a good way.) in Troubleshooting.I very carefully built "The Thing" from DeadEndFX, and the moment I plug in 9v, the LEDs light up. They're supposed to pulse with the...
-
-
-
Loading…
-
Loading…
