Search results

I was honestly just curious if and why it was ruled out? There is nothing wrong with it if you build a rat or rat like pedal. Like Robert said its just not as sexy to advertise but functionally equivalent and much easier to source a legit ic. Now if i was asked if I would like some real 308’s of...

You may want to check you power supply as well. It needs to put out at least 200ma. Not enough will likely cause it to not function properly.

Why not just go with an Op07 and call it a day? I have both and cant tell a difference. Plus you can get them from legit vendors and not have to worry about it. I promise I’m not trying to be an ass. It’s a legit question.

You might want to consider one of the current meter kits to measure ma’s in the future. It’s especially helpful for the tube pedals. To be honest I’m surprised it worked at all with such a small amount of power. https://www.pedalpcb.com/product/cmkit/

What are you using for your power supply? The wrecking ball will pull significantly more power than the other projects.

Okay so for my second one at first it would only tune and not pass signal in bypass. It was the opposite of yours, lol. Long story short after doing a lot of troubleshooting it ended up being a bad relay. I thought mine was clicking but I guess it really wasn’t. I supplied my own parts and...

It’s the current one. It matches perfect. I have used it myself and verified. It’s gonna depend on what you are using for your axis but it’s right. I’m not at home to get a better pic but I had this one. it’s the flesh wound in the bottom right

I actually finished this a few days ago but had some gremlins to work out. Tip, use pot protectors, lol. They were fine out of the box but once I boxed it they were shorting against each other causing wonky things to happen. The programming is still a little much for me but the planet series...

Here is my second one. Just dropped it into its new box today. Works perfect.

The jack looks like its touching I believe is what he is pointing at. Since thats the tip of the jack that would cause a short and cut the audio out. I would try turning it a little so you don't have to worry about clearance. If its not passing audio in bypass or active look to the jack, lol.

Just finished up the Maelstrom. Its based on the Darkglass Microtubes B3K. Great Bass overdrive. It can be clean or get really crunchy. Lots of different sounds in this box. It will definitely live on my bass board. I wish i would have found this one sooner.

I have to admit i am already thinking of which pedal to try this on. Thanks for the write up.

Technically it should still work. The connecter is a little finicky to get seated properly. You may want to gently pull it out and try re- seating it. Don’t force it but make sure its all the way in on both sides. I actually bent the whole group of wires to make it more of a straight shot to put...

Got this one finished off this morning. What a cool pedal. It almost goes into snyth like areas when you have the octaves cranked. This will definitely be one of those find a place on the board pedals. I have never really messed with an octave pedals like this is it’s all new territory. This was...

Your welcome. Just take your time. It’s a great build. With a little practice the stacked boards are just like any other build, they just fit in a smaller box (usually, lol). When you have multiple headers like that too, you may just want to solder one leg of each one first. That way if it’s not...

This should work. You will have to do a little work though. You may just be sble,to replace the one wire. If not you can get an extra screen and I can verify that it does work...

So I didn’t really have any expectations going in. I generally don’t like tons of knobs on delays, I like them pretty straight forward. This one, with some fiddling, got some really nice delay sounds. It seems like it could be really versatile. On the other end there are some settings that are...

Yes, the longer screws are for the 125b. It should be pretty snug and not move at all.

Fixed. Not sure what was going on.

I need to figure this out. Right now i have edited a 125b foot print that has knob placements etc. i i place it temporarily so i can have my pots in the correct place. It also helps me draw the board within the correct dimensions. In eagle i had the hole board pre done based on pots. Already...