Search results

  1. BrainDrain

    Deadendfx Reflektor no delay signal

    Ohhhh ok. It caught my eye and just wanted to make sure since that pedal is a bit more dangerous to build than the average 9v circuit. Glad everything worked out!
  2. BrainDrain

    Kliche Overdrive - No Input?

    Ok so it sounds like your footswitch is ok. It has to be a solder joint somewhere or a broken trace. The traces that connect to the solder pads are very delicate. If one gets too much heat during soldering it can break off from the pad and it will be somewhat hard to see. You tested all your ICs...
  3. BrainDrain

    Kliche Overdrive - No Input?

    Wiring looks much better now. Does your led light up when switched on and humming? If the footswitch tests ok with a continuity meter and you cleaned up the bottom of the board then it’s time for the audio probe. Double check all your resistor values too just to be sure. Usually it would still...
  4. BrainDrain

    Eternal Burst board

    Stick with whatever the pcb is labeled as. The pcbs go through different revisions sometimes.
  5. BrainDrain

    Kliche Overdrive - No Input?

    Not working in bypass means it’s wiring/bad joint or a broken trace. More likely the first. Foot switch could be bad or could have had a bit too much heat put into it, but that’s not that common either. I’d still check it with a multimeter continuity test to see if the lugs are connecting in...
  6. BrainDrain

    when to use mlcc capacitors

    Always read that too and mostly followed it. Except the almighty Fuzz Face totally goes against it. Lol.
  7. BrainDrain

    Kliche Overdrive - No Input?

    Does it pass signal in bypass? If the pedal is powering up and LEDs lighting it’s probably not the power connection. Most common culprit is a bad solder joint as already mentioned. Could also be a broken trace that isn’t able to be seen. Essentially a factory defect. Not as common but it’s...
  8. BrainDrain

    Deadendfx Reflektor no delay signal

    Build looks great. Glad you got it working. One thing I noticed is that it looks like your output jack ground lug is connected to the pcb ground, unless I’m just seeing it wrong from the picture angle. I think that one is supposed to be left disconnected to prevent ground loops since it’s...
  9. BrainDrain

    Deadendfx Reflektor no delay signal

    How much is the UK shipping? I usually pay around $20-30 to have them shipped to the U.S. when I buy from Dead End. I usually order a few different pcbs each time. Dino is one of the most honest people I’ve ever come across in this hobby. If the actual shipping cost comes out to a decent amount...
  10. BrainDrain

    Deadendfx Reflektor no delay signal

    Same here. Hit me up if you run into anything funky.
  11. BrainDrain

    Deadend FX Reflektor low volume

    Great news! That makes me happy you got it working. I was anticipating issues with mine before I even started it. LOL.
  12. BrainDrain

    Are these 1S1588 counterfeits?

    Lmfao 💀
  13. BrainDrain

    Elysium Ambient Delay - Time pot noise

    I need a 3D printer just for stuff like this. I don’t mind buying the ones from this website but those look like they fit nice.
  14. BrainDrain

    Deadend FX Reflektor low volume

    1. Do the voltage test points measure correct? 2. PSU is AC output right? Not DC. 3. Did you use the 50k trimmer for R29? And if so did you play with it? There might be a very narrow range of where it’ll work. I know Dino tests the included chips for this one before sending them out so...
  15. BrainDrain

    Elysium Ambient Delay - Time pot noise

    It might not be the issue but Electrical tape under the pots isn’t usually good enough to do the job. Especially over time. You need plastic pot covers or at least something thicker than tape on the back of the pot. Some people stick or glue a little piece of thin cardboard but I wouldn’t...
  16. BrainDrain

    Are these 1S1588 counterfeits?

    There’s only one reason those diodes are magical: They keep the “waiting list” and hype alive for the KOT. And I don’t even mean that in a negative way at all. Is what it is. But imagine having someone in the audience come up to you after a gig and say: “dam dude….the knee on those diodes is...
  17. BrainDrain

    PT2399 Sourcing

    Rowin LEF-303 check out this forum post.
  18. BrainDrain

    PT2399 Sourcing

    I use Amazon mostly and Tayda when I put in a big order. They seem to be the cheapest at those two places but it’s been a while since I looked elsewhere. I think I paid $7.50 for 10 of them. On Amazon they’re labeled as Bridgold brand and have worked great. Never had a dud yet. They have the...
  19. BrainDrain

    Stuff you wanted to know but were afraid to ask

    I love just a regular stainless flat washer outside. Simple and classy 👍🏻 Supposedly the Belleville style washers are what NASA and the military likes to use for locking.
  20. BrainDrain

    Stuff you wanted to know but were afraid to ask

    Some of the best footswitches come with lock washers. It’s just a choice of the manufacturer or possibly who’s selling it. Personally I’m not a fan of smooth spring washers on anything that has pressure always being applied to it. I’ve never had them work well for me and the switch always feels...
Back
Top