Search results

Thanks for the quick response I'll try the film cap and I read about nonpolar caps being polarized just never felt that in pedals it would have any noticeable difference but I really liked the quick and dirty cap polarity test makes sense to my ears now that I can hear the difference. I figure...

The 470nf tantalum cap in this build , can I sub it with an electrolytic? I'm sure theres a good reason for choosing to put a tantalum there but I don't have one and as usual I'm inpatient and don't want to wait unless its critical to the circuit also being that its a 470nf if I was able to use...

Built the Module8 worked perfectly first try. There it sat on my board 4 days enjoying the hell out of it ... Fast forward Got home today plugged in and no effects I get a kind of very slight phase on all programs and the pots don't do anything I get by-pass signal just fine. Anybody come...

Well I finally got more 13700's. Swapped out IC3 and still the same with one small twist when switched to vibrato mode the sweep pot acts and sounds as it does in phase position unless this is normal function when in both positions.

you people are awesome with the quick responses thank you very much for the info

Is this the correct regulator to use? From Tayda .....L78L33ACZ 78L33 + 3.3V Voltage Regulator IC i was'nt sure because of the extra letters at the end. They are already ordered and could be used for something else if they are wrong. thanks in advance to all.

Is this the correct crystal? the title is a bit misleading https://www.amazon.com/ABRACON-AB38T-32-768KHZ-CRYSTAL-32-768MHZ-12-5PF/dp/B00LQPAMJM/ref=sr_1_1?crid=2IZJA1IG8WMU3&keywords=ab38t-32.768khz+crystal&qid=1662913522&sprefix=ab38t-32.768khz+crystal%2Caps%2C195&sr=8-1

thot so thanks

can I sub 1n4148's for the 1n914's?

thank you what I wanted to hear

Would using 10.1K resistors instead of the 10k the arachnid calls for have any ill effect on the pedal. It's all I have at the moment.

Just asking … you think there’s better odds with e-bay over Amazon? Or just price wise it’s better?

just saw this yay or nay? I wouldnt know but seems cheap, no? hope the link works https://www.amazon.com/dp/B07BZBG7DY/ref=aod_recs_desktop_prsubs_2

i definitely would try a tonebender. I just assumed germanium was the awthentic way to go and the silicone ones were a psuedo fill in for whatever reason but I didnt really give it much thought . those 2 trannies are easy to get so its on the list now. And I gotta say I really did like what I...

Ive yet to build any fuzz face or tonebendr variants. Mainly due to most trannies from back then (this opinion based off all that I've read) either impossible to get or waaaay outta spec and lastly I find it hard to justify paying 12-?$ for a transistor that I'm unsure I'll like. I've found that...

thanks for the link . good reads.

So I am always ALWAYS looking for the newest(or oldest) best sounding ultra screaming od/disto Cause 1 I cannot afford any tube amp that I like Cause 2 Even if I could I couldn't crank it where I live So i got a Yamaha G-100 head with a decent reverb a pretty nice tremelo a super shitty...

Ok so reading about the arachnid and being clueless to EEPROM the arachnid is what? You swap out preprogrammed EEPROMs and get different effects ? If it’s as simple as that I’m in. Programming EEPROM s? Later. As long as I can get preprogrammed ones I’m assuming not every pre programmed one will...