Search results

It looks fabulous! Especially the powder coated chassis gets me everytime I see the Rosamp kit. And thanks for the link to Robs startup page. I need this. Last week I was so out of my mind that I fired up my first tube amp without a load and measured for like 15 minutes until I noticed... All is...

I like it with the Baja SVT. But everyone might drop their favorite Preamp :-) If you want a ready to use pcb an svt is the Aion Artemis (Catalinbread SFT).

5 lines are free 8€ per line after that. I ordered 6 enclosures which should have the same hs code so I should be fine. edit: it means that fedex should put all enclosures in one line as they are the same code according to the german customs manual.

DHL are a bunch of… There is a looong thread on reddit about this issue https://www.reddit.com/r/diypedals/s/DzYmlMf5pl I placed my first tayda order today with fedex but only 6 items. I hope its without a hassle.

Always check the dimension of the resistors! I had the musikding kit and unfortunately not all resistors are from the same manufacturer (series?) and therefore it is a tight fit. The larger resistors do not touch the pcb.

Ok, I set IC4 Pin 3 to 6,6V by adjusting Bias2 but then the wave form on pad 3 with looks super distorted. 7,5V is the cleanest looking wave form. With 6,6V in the end the effect is less noticable then before. I mean.. it's there for the Flanger and the Double Tracker and it was there but a bit...

My measurements are like the ones from jwyles90 in regard of the higher voltage IC4 pin 1, 7 & 8 and I think this is ok, I saw this in other posts. IC3 1 14,92 3 7,46 4 6,96 5 0 6 7,46 7 7,32 8 7,32 IC4 1 14,9V 2 7,46 3 7,53 4 0 5 0 6 7,45 7 8,16V 8 8,0V

Hi there, can anyone explain the purpose of the vactrol in this circuit? Is it just for the bypass? https://drive.google.com/file/d/1hw0JzsKDqhu4u8Q1LXFpuT3oaby-f_XB/view

No it's not related to the LT1054. The cancel trimmer is for the clock noise of the 3007 and it should be less in the middle position of the trimmer but it's not.

In this thread are various formats but you could ask @Chris420 (offline for a while) or @jeffwhitfield if they can share an svg with you if you use Inkscape etc.

I have the same problem with the cancel trimmer. Anyone else having this issue? The support forum is not really supportive :-) The pedal itself sounds good. Clean the effects could be a little bit louder. I tried to tune it with an oscilloscope and that is the only way I can achieve the 10%...

But soooo expensive!!!!

Well… Not that easy to get everything ready to build. Tayda would be the best guess. You could buy the kit and predrilled enclosure (blank aluminum) from musikding.de and spraypaint it pink. Or buy the kit and get a pink enclosure from...

Thanks for the kind words and thanks for asking! I spotted a mistake while trying to explain... This is how I did it: I lifted pin 1 and 8 connected switch pin 2 (red) to the bottom of the pcb where the ic pin 1 was connected connected switch pin 1 and ic pin 1 with pot pin 1 connected pot...

So let's build rev 4 and do some rerouting?

Is there a way to check where the oscillation is comming from? I mean I started cutting the long input trace and wired the jack direktly to the input but unfortutelly that was not the issue :-)

The chalumeau of the guitar world. I made an attempt to make the pedal switchable without the fuzz. I was only partially successful. I may have to solder a pull-down resistor to the input, I think I read about it somewhere. Pin 1 and 8 of LM386 have been bent up/broken off and are connected via...

A picture but you cant really see something The parts all have the correct value. It is working except for the oscillation. The traces are ok. Some caps melted while I replaced some parts. LEDs missing. Maybe the layout in general is the problem.

Ok I forgot to add some files. It's not on strip board it's a produced pcb. Dumb as I am I use new circuits and put them in projects... The difference to the original version is that I hooked it to one supply with two other effects and added a 100n to each IC. My schematic is attached and this...

Hi everyone, I wanted to ask the collective intelligence in here to help me with a pedal. On FSB there is a new Baja Reactor V5 which I put in a combo pedal consisting of Reactor, Unicab and a Headphone amp. https://www.freestompboxes.org/viewtopic.php?p=300036#p300036 The reactor is causing...