Search results

I have been working on something somewhat similar to this as well. I would consider an 8 way rotary for the clipping and set it up with something like no clip, led-led,led-4148,led-bat41,4148-4148,4148-bat41,bat41-bat41, and maybe just lock out the last position with the washer. The build I am...

If you keep this up I might end up with a JLC order of just your boards. Awesome job again!

Either put flux on them or sand/file until you expose some copper. Make sure your iron tip is clean and has a bit of solder on it. Heat both the wire and jack. If you have an adjustable soldering iron bump up the temp some.

That’s a cool layout on that. It’s one of my favorite lead tones also.

Well you got my mind going on this circuit. I think the gain 1 and 2 might not work correctly as the diodes aren't modeled but it should give a good idea of part changes and how the effect the EQ curve...

I would try gently running the tip of a razer along these 2 lines. I think this track might be connecting to ground.

I had more planned for this circuit but the mods I had planned I couldn’t find a way I was happy with to implement. That being said I build this mostly to the PS-20 bass specs but did use a few of the guitar resistor values. I’m pretty happy with the sound. I oddly kind of like it into the...

i think the filtering on this pedal is fairly interactive with itself. That being said I think what you are looking for is to adjust the range of one or multiple high pass filters and that will open up that range some. I think it might be kind of hard to do by taking random stabs at it. You...

The Electrosmash article https://www.electrosmash.com/klon-centaur-analysis has some good stuff about this. If you look at the gain calculation section it shows that there is a mid peak that develops as the gain is increased. It looks like it shifts from 500hz to about 1khz as the gain is...

I think that’s leg 5. I would just run a jumper from the IC pin to any of the locations circled in red. Just make sure you have the correct side all the red points should have continuity. I can’t really tell if the solder joints are cold or overfilled. Some look a little cold. I think the...

Here I am thinking about doing this one and you’re already done. The other one I have been considering is the Dylan 159 trembling satellite but it isn’t a harmonic trem.

Very cool pedal as always. I didn’t realize you had a GitHub for your boards. I may have to throw one in with an order soon.

If you pull up pins 1 and 8 like in this pic. Then solder either a switch that goes between open and closed and you will get a 20 gain and 200 gain setting or wire in a 1K pot and you can have a range. It’s an easy mod as the work is all done to the IC so if you mess up you can just get...

For the average person that makes sense. I have a stash of cheap pickups I have been thinking about what to do with. They aren’t really worth the effort to sell but I wouldn’t put them in a guitar either.

This one is interesting I have experienced this with fuzzes but hadn’t considered a solution before. I’m wondering if you could do the same with an actual pickup instead of the transformer.

I'm starting on designing a V2 circuit board for this. It will have some changes based on what I have learned since I came up with it and some experimenting I have done. This will replace the high control on the previous circuit...

I think you have a 4.7R resistor instead of a 4.7K resistor in the CLR location.

Hey FF, You know there aren't many Animal Alliteration (AA?) screen name folks here. I haven't gotten too far on this it's about number 10 in my pile I have been sidetracked with some home projects and my Rat PCB design. What I was considering was something like this. Bridging these two...

I don’t think I have seen a build report for one of these before. Am I the first? This is a pretty sweet semi parametric. EQ sweepable mids from 300-3300hz + or - 16bd. Switchable from high to low Q. Baxandall bass and treble 15db + or -. Volume control works well good cut to match and...

I had been doing the separate shield and ground but now I am mostly grounding the shield at the jacks just because it’s neater. The isolating washer is just a best practice type thing that I was considering messing with. Some of the other things I have run across that are grounded this way is...