Search results

From the looks of it, the lifted pad will be easy to deal with since it appears that it's connected to the component right beside it. You can probably just ugly bridge solder across when you solder in that component. Looks like a pretty simple layout!

Good news is, you _should_ be able to see this state of affairs in the UI. After you upload the BOM and CPL files, it shows you a rendering of the board. And someone at JLC does check it, even it you don't have the option checked, when they're setting it up they'll email you if they spot...

The bom looks like: Comment,Designator,Footprint,LCSC,Quantity 10K,"RV1,RV4",RTRIM3362P,C118956,2 Conn_01x03_Socket,"J1,J2",JST_PH_B3B-PH-K_1x03_P2.00mm_Vertical,C131339,2 100pf,"C19,C21,C22,C23",C_0805_2012Metric,C1790,4 1n5819,D1,D_SOD-323,C191023,1 100R,R1,R_0603_1608Metric,C22775,1...

I've been adding some THT parts to all of my designs. Sometimes box film caps for larger values, and always JST connectors for the footswitch board. It adds a bit of cost (since there's a $3.50 THT setup cost even if you just add one component) but it's worth it to me for time savings. I...

Couple of things: - If you have it done with PCBA, to use their 'Economic' service, you'll need to create the panel with mousebites instead of V-cuts which also means that you need to panelize it yourself rather than using the built-in JLCPCB panelization feature (which uses V-cuts). You can do...

Yeah - TL072s are relatively cheap in quantity and they're in almost every pedal. And if they're not in the pedal, a lot of the time they can be subbed for whatever opamp anyway - dual opamps have a standard pinout so things that call for NE5532, RC4558, etc can generally at least function with...

I built a board using through-hole components and wanted to see what the JLCPCB assembly would look like for a purely through-hole board. For purely through-hole, there's no setup cost and no stencil fee. However, the cost-per-unit for assembly is a lot higher. For really small runs of boards...

It's possible that's an issue - are the other pin 8's also noisy? (There's a small resistor between which might help the noise though). IC4 is part of the LFO (low frequency oscillator) so it's not super unusual for stuff in there to make weird noises but it is odd for the VCC pin itself to be...

I haven't gotten this all breadboarded, but I just yolo'ed a through-hole PCB layout and will order a stack of 'em next time I order from JLCPCB, and see how it works. If it makes any reasonable noises I'll release the gerbers for people to try out.

Worst case you can probably just bend those pins out from the socket (cuz you used sockets right?) and bodge it to VREF somewhere. If you did SMD or soldered right to the board it'll be a little harder, but should be at least hackable without getting new PCBs made.

I think pin 3 and 5 of IC2 should be tied to VREF (Vb) and not 9V. (9V maybe a holdover from using a charge pump where it was halfway between 18v and gnd?)

Good thorough notes! I think there's something wrong at IC2/3. That pin is tied right to VREF_A and other things that are tied to VREF_A seem to be okay, but that one is ~zero volts - so either it's floating unconnected or it's near-shorted to ground. Check your socket there there there...

I think something's wrong around VREF. Pin 3 and 5 of IC2 (middle) are both tied directly to VREF and they're showing 3.5V instead of something around the 4.7V mark I'd expect at 1/2 of 9.45V. Pin 3 of IC1 (right) is also tied to VREF through a 1M resistor and is only 1.16V which would muffle...

Pictures of the soldered side would be helpful (though of course kind of difficult to see everything with the pots in the way). Pot in bottom right of picture looks suspiciously soldered. (Middle pin may not be making contact). Dunno if that'd cause those specific issues or not. Really all...

I was trying to to figure this out, too - I think what it means is that in the "classic" BBDs there are two separate clock pins that step back and forth, leading to potentially more complicated offboard circuitry, where this chip just has a single clock pin that expects a square wave input...

If the BoM doesn't specify, it's probably fine. You could socket the transistor if you _really_ wanted to try to tune it, but for most pedals, something in the general vicinity of the gain range will be fine. There are some designs where it's important to have one transistor with less gain...

Regarding the transistor, the letter at the end of the transistor often indicates the gain range of the transistor. Manufacturing transistors is somewhat inexact and the gain can have a pretty large range of values. Manufacturers will do 'binning' where they test parts from each batch and sort...

I think your vref is off. Looking at R12 and R13, they should be the same value (47k) but the multiplier bands look like different color - R12 looks like it might be 47K (Yellow Purple Black Red Brown) and R13 looks like 4.7k or even 470R, the lighting is not great (Yellow Purple Black...

Have you tried it out of the enclosure, like just moving the input wire out of the way? (Rather than going thru the hassle of shielded wire). I think that'll help figure out whether or not shielded wire would help. I think running near/over the 9v rail is probably ok, though maybe not...

@Reconciledheart I did play around with this on the breadboard a bit this weekend for funsies, with a bipolar supply (+9/-9V). I got as far as the main gain stage, I haven't gotten through the whole tone stack part yet. I might try it again next week with a unipolar supply + vref to keep the...