Search results

Hello MiKL The Malachite was modded to have less gain in the previous stages so that I was not clipping the signal into the LEDs if the gain was turned down, even on the blue mode. I also socketed the LEDs so I could remove them to ensure no clipping but I found that I liked to have a little...

Any timeframe on how close to the Doxie schematic is to being released? I want to increase the top end of the pedal so it isn't so dark sounding straight into my Helix. -Sean

TS5 into the Plexfeta(TM). Switched back to 1960A speaker emulation. Everything on 10 (max) except Volume (output level) - Recorded directly into Reaper using a UAD Volt 276 and Line 6 Helix Native software for speaker emulation, no eq or effects - Speaker emulation used on -01: Dual 4x12...

Here's a favorite setting on the Plexfeta that I think shows a good dynamic capability from fairly dirty to clean. - Recorded directly into Reaper using a UAD Volt 276 and Line 6 Helix Native software for speaker emulation, no eq or effects - Speaker emulation used on -01: Dual 4x12 Greenback...

TS5 (only TS that I have on hand) into the Plexfeta(TM). Switched to Greenback 25 speaker emulation. Everything on 10 except Volume (output level) - Recorded directly into Reaper using a UAD Volt 276 and Line 6 Helix Native software for speaker emulation, no eq or effects - Speaker emulation...

Evidence Settings: Everything on 10 except Volume (output level) - Recorded directly into Reaper using a UAD Volt 276 and Line 6 Helix Native software for speaker emulation, no eq or effects - Speaker emulation used on -01: Dual 4x12 1960A, stock settings (mic: 57, Position: Cap Edge...

After building my first Mofeta board and playing around with it and letting my bass player use it (and ultimately keep it), I decided to make a second one. I made provisions for a few tweaks but ended up using the stock components for that build as well. I have really enjoyed the different...

Gator, Yes, I noticed that the Malachite was darker in tone than the other two Revv clones. I built a Sanguine with the gain of the Malachite but the standard Sangune tone stack. Gave a much brighter sound, so much so that I had to dial the treble down to almost 9 o'clock to stop my ears from...

Hello Everyone, I've been on a multi-pedal kick lately so I made this up for my bass player. He loved the growl and tone of the Mofeta but wanted something to kick it a little and get some nice dirt. So, I took his Mofeta and made it always on and then added the Kliche mini SE (with Chuck D...

I just finished up re-boxing my Paragon Mini. I needed a smaller enclosure so it could fit on my pedal board. I found the 1590B3 encolsure and I modeled it in Solidworks to make sure it would fit. I had to find smaller toggle switches since the old ones would not fit. I found some subminiature...

@iamjackslackof Solidworks is the 3D modeling (CAD) software that generates the models. Then you need a CAM software to generate the toolpaths that are used to ultimately generate g-code (what the CNC controller uses to run the mill). I used the Arduino IDE to write the code for programming...

@iamjackslackof My cnc setup for pedals is just a small taig mill. It has a large enough work envelope that I was able to mill out all of the holes on both the front and top mount jacks/power. When I drilled by hand, I noticed my drill bit wandering ever so slightly and that caused the knobs to...

All, Thanks for the kind words. It is nice when a plan actually comes together in a surprisingly good way. iamjackslackof, I tried drilling my first few enclosures by hand and I wasn't happy with how accurate my drilling was. Now I don't drill the enclosures. I mill them on my cnc mill. I take...

Greetings everyone! Since my last triple pedal build, I have gone on to build a few different versions of the Revv clones (dual pedal of the Tyrian with Sanguine tone controls and Sanguine with Malachite drive levels, a stand-alone Malachite modded to clean and bright, a triad fuzz and a few...

So, I have finished by triple pedal build (check the Triple Pedal build log showing my Sanguine, Tyrian, and Malachite all in one enclosure ) and really love the pedal. I use all three running into my HX Stomp XL . They all sound great with the exception of this one issue with the Sanguine. When...

Joben, Thanks. I have a Taig CNC Micro Mill that I used for the enclosure and pcb for the custom switcher I made. -Sean

Well, it's finally done! Sounds Fantastic! A little different than I expected but I like it! The custom switching system works great and the Stack feature allows me to stack the 2 with either 3 or 4 to get a more thick OD sound. Sounds great by itself but also sounds great with the Paragon...

Here's an update to my build. Just finished the three main boards. Now its just a matter of wiring it all together and making sure that something is making a connection that it shouldn't be. -Sean

Thanks everyone! It's nice to have some positive feedback for my crazy ideas! Fig: Awesome name! Hope you haven't trademarked it yet ; ) I may have to fire up my CNC mill again to engrave that name on it! Feral Feline: I can't wait either. Looking forward to this. It should work well into my...

Hello Everyone, This is my first post here. This is not my first pedal build (Cheese Monger and Paragon Mini were first PedalPCB units) but it is my first triple pedal build in one enclosure. Thought I would share since I got the idea from this forum. Here is what I have so far. I am working...