Search results

Here is a Resinite OD (Amber Overdrive), probably my favorite distortion circuits. While making this I learned it's a big muff, and I don't know how I feel about that. I wanted to make it without any off board components. It uses these jacks which are smaller than the Neutrik style. I was...

I'm watching a ton of vids on board layout, mainly on how to reduce or eliminate noise. I'm noticing that they all seem to be based on boards that operate with freqs in the mhz and ghz range, and/or have switching power supplies. Our boards are in the much lower audio range and have a low...

I'm doing this now as well. I'm thinking the flat plastic part of the jack that the threaded part sticks out from should be flush against the inner wall of the enclosure. The jack should be nutted (smh) onto the enclosure semi tightly so it is secured but still able to be rotated, and then the...

LEDs come in a range of brightness. If your LED is too bright then increase the 4k7 resistor to something like 6k8. It's helpful to set up a small breadboard with an LED so you can try different resistors and get an idea for what you want to install to the PCB

This needs to be moved to an after hours discussion...

Try different op amps for that light distortion. The TL072's you have look sus The middle pin of the L78L05 is supposed to be ground. If you are getting continuity between pin 1 and 2, then your 5v supply is shorting to ground somewhere. Check anywhere that 5v is present, like Q2, Q3, and the...

24ga stranded silicone insulation

The grounds are fine as it is. Each ground is connected to each other so it doesn't matter where they go as long as they are all linked

I harvested my tants from a failed project so I've done my good deed for the year

I drew this up - it's the same circuit as before (Mastema Drive) but laid out on a 1590bb with everything mounted to the board. If this were a pedal I would make, I would use the audio jacks that have a collar nut that secures from the outside. The power jack would be recessed, and the LED trim...

That looks great! I love the striking blue PCB

I love seeing old Fender and Gibson guitars that have a big ceramic capacitor for the tone control. I think of this kind of discussion every time. https://www.rickn-guitars.com/electricals/gib_electricals.html NOS High Voltage Ceramic... "excellent sounding" It may be that the limitations...

I use MLCC when the only alternative is a ceramic cap, or if there isn't space on the board for a film, or if for some reason the build doc calls for it. For instance, I'm building an Aion Xenotron, which needs 100nF MLCC's for the power supply and BBD filtering sections. Typical values for an...

It's okay. It's worth taking the time to do it slowly and cleanly because it'll save you more time later on This is a Skylight Overdrive, it's a Mad Professor Sky Blue circuit. Just remember with soldering, go slow and try to enjoy it. You will develop speed thru repetition.

The most common culprit is poor soldering. In your power jack alone you can see stray strands of wire. That kind of thing needs to be cut short. When you solder, start by stripping off 1/4" of insulation from the wire, twisting the strands together, then tinning the wire. Tinning is when you...

I've noticed what seems like your earlier layouts are 1590b sized and the component fit is very tight, like on the Seabed Delay. I like these boards as they look great and are very satisfying to build. The (presumably) later boards have components spaced further away from each other. Is there an...

Go in and clean up your wires esp at the power plug. Also your input jack connections are backwards. The ground is correct but the bottom lead in your pic should go to the battery

I have a couple sets of these which I like because they are configurable - the drawer housings come apart so you can set them up however you want. I also have two of these, which take up a lot of space, but it's really nice having an entire drawer for each resistor value

Dang, I never even thought of that. I'll try to keep that in mind with the next one. The power is DC and the signal path is low voltage so hopefully it'll be ok!

This is my first shot at a PCB - I went for an MXR Il Diavolo, one of the first pedals I really liked. I wanted it to be a certain layout so it can fit it in a double board project I have in mind. It was difficult to figure out the priority some of the components need when being laid out. Also...