Search results

  1. J

    Low Ballers question (hypothetically of course)

    There's no DC on that cap and a film cap should work fine
  2. J

    SOLVED Caesar Chorus No Output

    Do you have a condom on the lower pot?
  3. J

    Silismile Fuzz problem (low volume/fuzz output)

    K. Pinout is correct. Is that plumbing solder? That's really large gauge for electronics work I would reflow all your joints. There's a lot that aren't great. Solder should flow through the through hole at least flush to the other side of the PCB. you have some pads that are even full on the...
  4. J

    Silismile Fuzz problem (low volume/fuzz output)

    What transistors came with your kit? 2222s? BC1xx? Can't see in the photos
  5. J

    Silismile Fuzz problem (low volume/fuzz output)

    Check transistor orientation/pinout
  6. J

    Ultrasonic cleaners

    Sorry. Hell of a week. What Darwin said. Blown amp or bad voice coil...
  7. J

    Ultrasonic cleaners

    I mean. You gotta take it apart first. If there's power getting to the transducer you can possibly just replace the transducer with Ali parts
  8. J

    TC1044 TO LT1044 SWAP

    Try moving your cable in away and in general to see if it changes intensity Otherwise, audio probe Being strip board.... Well. Yeah.
  9. J

    Critique my circuit

    Yo circuit so fat... Jk. Should use or terminate the other opamp.
  10. J

    white 6mm d shaft push on knobs?

    Or glue some spacers on https://www.harfington.com/products/p-1465860?c
  11. J

    white 6mm d shaft push on knobs?

    https://www.stlfinder.com/model/crate-amp-knob-M24Kwcjz/3331212
  12. J

    white 6mm d shaft push on knobs?

    Gotta find the Harry Klipton of CRATEs Edit: Stoopid autocorrect
  13. J

    Switch simulator - bypassing pedal auto power-on state

    I think you could hack this with a PUT (2n6027)and a couple diodes. Input voltage to anode. Diode to gate. Need at least 0.35v drop below anode. Then take the cathode out to wherever the ON switch is. Use another diode to drop the voltage to the required level (so if it's a 5v relay, use a 5v1...
  14. J

    2N3565 Orientation

    Flat spot is emitter. EBC pinout What PCB are you populating?
  15. J

    Buggfx Daydream no wet signal

    Tis the season for ESDing. Take care with eeproms, logic chips and bbds.
  16. J

    Buggfx Daydream no wet signal

    Actually, at least from the photos, leg 15 *may* need a touch-up. Dab of flux and a kiss from the iron won't hurt. There's some new guy soldering fv-1s over at ppcb
  17. J

    Buggfx Daydream no wet signal

    Sounds like an issue with the eeprom or interconnects to it That's the internal programs you are hearing. Pull the eeprom(note, they are ESD sensitive) and test for 3.3v, ground and check resistance to the legs 6/14 and 7/15 eeprom/fv-1. I wouldn't use diode mode here. Use resistance. Some...
  18. J

    Buggfx Daydream no wet signal

    Check clock on pine 9/10 if your DMM has a freq count feature or you have an oscope Lift one side of R5 and see if the internal programs work.
  19. J

    A question for those that have a zoom cdr70+

    Maybe? https://aionfx.com/project/elysium-ambient-delay/
  20. J

    smart phone holder that doesn't obstruct the lenses

    I believe what you seek is refered to by the youths as a "selfie stick"
Back
Top