Search results

Ok, pulled it all apart, and I have it working without the relay. I definitely needed a ground connection between the two middle jacks, but I'm pretty sure I had that before as well. Gate is working and the light is working right now. I tested the range switch pulled off and put back on again...

@Paradox916 have I got that range switch soldered incorrectly? I have all three points on the PCB attached to each pin of an on-on switch - if I check your build pic - which is obviously a heavy influence - I think you've only connected two maybe? I've pulled it from the enclosure and now the...

Aion Heliodor Not really that interesting I thought.

Aion Maelstrom - Vintage Microtubes spec. Had to do some resistor tenting and some other wierd stuff for this one but it does sound good. Trying to work out if I also need to build a B3K or if this will do me. the attack switch does nothing on this which is mildly annoying but apparently by...

Aion Azure chorus built with a socket for the bass capacitor, sounds pretty good! I made another Aion drive and on the drilling I did it down a little lower so the knobs wouldn't be so high, and then fucked myself over because then the switch board didn't fit, so it's on a massive angle lol. Oh...

Oh, the input was connected, just not in my initial photos. Here is how it is currently wired up, green between lower jacks tip to tip, and then blue off this to the T on the board. The switched tip is to the outer connection on the board and I have a ground to the middle at the moment. Do I...

thats gotta be it hey I'll fix it up and give it a test.

Nah its close but not bridged

The circuit is working as designed, it's just the led which I would usually use to indicate whether the effect is on or off, is on when the effect is off, and off when the effect is working. When the effect is off, the led is on and red when I am not playing, and green when I am, as I would...

ok, so after fiddling with this again, i have a new issue, but im hoping this one isnt too hard. I've got the muzzle working after sorting out a wiring issue, I had thought that the switched tip was going to ground on the jack, but its to a different pin - fixed that, and now the gate is gating...

I didn't want to build the muzzle unless I could find the chip and it had been out of stock for this site for months. Found one and ordered all my parts, by the time the Tayda order rocked up this week, Robert had the retrofit back in stock 🥲

I had also suspected that there would already be a buffer....sorry my schematic reading isn't good enough to recognise one when I see it. Even better I'll just pull it entirely. 👍

This is potentially more of a sanity check than anything else. I'm building a muzzle, and I'm using a basic relay, as well as a simple jfet buffer for what I hope is the input. I heard this circuit likes a buffered input so I figured internally would be good. It's just occurred to me that the...

An australian is generally up about $22usd for 3 or more $8 pcbs from PPCB, and we dont even have that tariff mess. (Not a complaint Robert, just an observation)

Haha, just seemed to us the epitome of "an attempt was made"

I have Australian grey butcherbirds in the reserve in front of my house frequently. I think I can hear them now as I type this and although apparently they also do impale food I've never seen it. My wife and I were walking along a nearby trail one spring and in a cut-through (it's a rail trail...

I can't bring myself to buy a metalzone because I cannot deal with side jacks. And if I want to order a PCB from GCI it's like $40aud to post. Please Robert, metalzone pcb

Fucking pissing myself that I picked that without having to look it up, then tried to sing it to my wife, then had to play it on Spotify while I sung your lyrics over the top. Thanks for that. Great work.

I'd just get them here. PPCB stocks j201. I've had no issues with the chop shop getting j201 to work as it has the bias trims, the desolate fuzz was a ... problem.