Search results

doh… it was renamed from „calamity“. now I found the threads:-)

Thanks! They came in a kit, I will forward this information to Musikding :-)

Hello fellow flux fume sniffers, is there a rule on when it's ok to use J113 instead of J201? I did build a few Pedals where I substituted the J113 and they were fine. The Desolate Fuzz does not work with them. I measured both J113. VG off -1,87V at ID 5uA VG on -1,01V at ID 5mA gfs 10,4mA/V...

Thank you!

If this thread is dead I will hijack it :-) I have an issue between Q1 and Q2 but I will figure it out. C3 and C4 are should be the only differents bewteen current pcb and the layout in the build document. @Robert is this correct?

It looks fabulous! Especially the powder coated chassis gets me everytime I see the Rosamp kit. And thanks for the link to Robs startup page. I need this. Last week I was so out of my mind that I fired up my first tube amp without a load and measured for like 15 minutes until I noticed... All is...

I like it with the Baja SVT. But everyone might drop their favorite Preamp :-) If you want a ready to use pcb an svt is the Aion Artemis (Catalinbread SFT).

5 lines are free 8€ per line after that. I ordered 6 enclosures which should have the same hs code so I should be fine. edit: it means that fedex should put all enclosures in one line as they are the same code according to the german customs manual.

DHL are a bunch of… There is a looong thread on reddit about this issue https://www.reddit.com/r/diypedals/s/DzYmlMf5pl I placed my first tayda order today with fedex but only 6 items. I hope its without a hassle.

Always check the dimension of the resistors! I had the musikding kit and unfortunately not all resistors are from the same manufacturer (series?) and therefore it is a tight fit. The larger resistors do not touch the pcb.

Ok, I set IC4 Pin 3 to 6,6V by adjusting Bias2 but then the wave form on pad 3 with looks super distorted. 7,5V is the cleanest looking wave form. With 6,6V in the end the effect is less noticable then before. I mean.. it's there for the Flanger and the Double Tracker and it was there but a bit...

My measurements are like the ones from jwyles90 in regard of the higher voltage IC4 pin 1, 7 & 8 and I think this is ok, I saw this in other posts. IC3 1 14,92 3 7,46 4 6,96 5 0 6 7,46 7 7,32 8 7,32 IC4 1 14,9V 2 7,46 3 7,53 4 0 5 0 6 7,45 7 8,16V 8 8,0V

Hi there, can anyone explain the purpose of the vactrol in this circuit? Is it just for the bypass? https://drive.google.com/file/d/1hw0JzsKDqhu4u8Q1LXFpuT3oaby-f_XB/view

No it's not related to the LT1054. The cancel trimmer is for the clock noise of the 3007 and it should be less in the middle position of the trimmer but it's not.

In this thread are various formats but you could ask @Chris420 (offline for a while) or @jeffwhitfield if they can share an svg with you if you use Inkscape etc.

I have the same problem with the cancel trimmer. Anyone else having this issue? The support forum is not really supportive :-) The pedal itself sounds good. Clean the effects could be a little bit louder. I tried to tune it with an oscilloscope and that is the only way I can achieve the 10%...

But soooo expensive!!!!

Well… Not that easy to get everything ready to build. Tayda would be the best guess. You could buy the kit and predrilled enclosure (blank aluminum) from musikding.de and spraypaint it pink. Or buy the kit and get a pink enclosure from...

Thanks for the kind words and thanks for asking! I spotted a mistake while trying to explain... This is how I did it: I lifted pin 1 and 8 connected switch pin 2 (red) to the bottom of the pcb where the ic pin 1 was connected connected switch pin 1 and ic pin 1 with pot pin 1 connected pot...

So let's build rev 4 and do some rerouting?