Search results

  1. Synchrony Pedalworks

    Burns Buzzaround PCB- Can you all review and critique?

    Sweet! That was an easy fix. Thanks!
  2. Synchrony Pedalworks

    Burns Buzzaround PCB- Can you all review and critique?

    @temol, @szukalski, and @neiltheseal - Thanks again for all the help. These comments are really helpful, and I am starting to see the picture more clearly. I recognize that the project is probably more ambitious, but I was going to give it a go for a couple more attempts. Let me know your...
  3. Synchrony Pedalworks

    Burns Buzzaround PCB- Can you all review and critique?

    @neiltheseal , @temol , and @szukalski - these are great suggestions. Thanks! Let me go back and give it a try without the auto routing and see if that cleans it up. @neiltheseal - your comment about the ground pour helps clear up my confusion, so thanks!
  4. Synchrony Pedalworks

    Burns Buzzaround PCB- Can you all review and critique?

    I am new at the PCB design (in otherwords, I have never done it), and was wanting to expand my abilities. I was hoping that some of the guru's could critique these PCBs and give me some tips. I used the PedalPCB schematic and layout for the Burns Buzzaround (@Robert - If it is not ok to do...
  5. Synchrony Pedalworks

    A multimeter that can read frequencies over 50hz

    I had the same issue too. I tuned it by ear. It sounds great, but it does make me wonder if it would sound greater if properly tuned…. I was told that the Fluke has a model that will measure the frequency.
  6. Synchrony Pedalworks

    DEMO [perf/wood] Maxon ST-9 Super Tube Screamer

    Wow! This pedal is stunning, from the wood PCB, enclosure and knobs! Where did you get the knobs?
  7. Synchrony Pedalworks

    Q-Tune DIY Tuner kit

    Oh, wow.... This is so temping... Great idea and I look forward to hearing more about the details.
  8. Synchrony Pedalworks

    VFE Merman via Madbeapedals

    @Guardians of the analog This was my first VFE build. I can understand your sentiment. The boards are tight and the parts unique. @jcpst I would give this Klon clone a try. I think it is worth it.
  9. Synchrony Pedalworks

    Fender TBP-1 Clone

    Speechless…. Impressive. 🤘🏻
  10. Synchrony Pedalworks

    VFE Merman via Madbeapedals

    I have a confession..... I am not a fan of the Klon. I recognize that is blasphemous, but it is true. I've make a few Klons, but never found the right one...until now. I cannot fully explain why this version is better, but the articulation of the notes is fantastic and it is easier to dial in...
  11. Synchrony Pedalworks

    Electric Canary Iridescent Delay

    If you are fond of delay pedals, then you should consider this project. It is a PT2399 based delay, but don't become biased against the chip. While it isn't "true" analog, it does a fantastic job. This pedal has the most features of any DIY delay that I have seen. It has modulation with...
  12. Synchrony Pedalworks

    General Tso troubleshooting

    With no sound for bypass or engaged, you need to check your off board wiring, either at the jacks or footswitch.
  13. Synchrony Pedalworks

    Which soldering iron do you like?

    Ahh, that could really help. Great idea!
  14. Synchrony Pedalworks

    Which soldering iron do you like?

    @Robert I just got the Hakko FX888DX model. My old soldering iron had the tip seize in it, and I couldn't get it out. Can you point me in the right direction for the barrels that you are mentioning in your post. Thanks!
  15. Synchrony Pedalworks

    Phaser Folks: EHX Small Stone vs Boss PH-1R?

    Of the two, I preferred the PH-1. However, I like the phase 90 best.
  16. Synchrony Pedalworks

    Uraltone TV Reverb amp

    The guts are stunning and clean. Great work
  17. Synchrony Pedalworks

    Carcass Fuzz

    That enclosure color and pen choice is fantastic. Very nice!
  18. Synchrony Pedalworks

    AionFx Zenith

    I run mine with a boss switcher, so it does see a buffer. I will have to try it naked and see if the effect changes.
  19. Synchrony Pedalworks

    Uni-Vibe and Surprise Preamp (AionFX Straylight)

    I totally agree that this is a fantastic pedal. It is always on for me, mainly with the preamp running, but I also have the vibe running. I also agree about the AionFx breakout boards. My pet peeve is to have to troubleshoot a pedal. You find the problem, fix it, and rock it outside of the...
  20. Synchrony Pedalworks

    DEMO The Gnat Fuzz!

    There are a lot of talented builders with this forum, but I love your stuff. The hand painted art is fantastic and shows a level of skill that a lot of us lack.
Back
Top