Search results

Hi DeMan_85, I just looked and the HX Stomp manual and it recommends using momentary switches. I could think of several reasons why and why not to but I would just follow their recommendations on that. To set up the exp pedal/toe switch do the following: Enter Global Settings > Preferences Set...

Hi DeMan_85, 1. The wiring is very straight forward. I have attached the schematic to help in sorting this out. 2. There is no need for a on/off switch as the software provides the latching so a simple on-(off) switch works. You can use a latched switch but you need to change the settings...

This is the switch I used: Mouser part no.: 691-110PM-OFF This switch has 6-8lbs of actuation force. works great for this application. You have to really WANT to activate this switch which is better than the other alternatives of 2lbs or less actuation force. You will also want to use this...

I've built the Bobby and the Doxie. I reduced the gain in the Doxie to make it sound more like a blackface (cleaner tone as opposed to more breakup) and it sounds very good. The gain of the Bobby would be reduced in a similar was as to the Doxie, by increasing the value of R3 and/or R5 from the...

Funnel, Thanks. Its taken some time but I am really happy with this setup. I have been working on this type of system since I got an HX-Stomp and realized I wanted more buttons and upgraded to the Stomp XL. The amp-in-a-box type pedals allow me to still have the feel of a real amp with all of...

Hello Everyone, After searching and finding nothing in the small DVP4 sized form factor with a toe switch, I decided to mod a DVP4 for a toe switch. I wasn't sure if it would fit but once I had the pedal gutted, there was plenty of room. Its a tight squeeze for the switch and jack as I didn't...

Hello Irgaraujo Thank you for the compliment. I have not noticed any issues with the three charge pumps running from the same supply. I am also running the arduino based switching system from the same supply that supplies the three pedal boards. Still no issues with noise, even with the pedals...

Hello MiKL The Malachite was modded to have less gain in the previous stages so that I was not clipping the signal into the LEDs if the gain was turned down, even on the blue mode. I also socketed the LEDs so I could remove them to ensure no clipping but I found that I liked to have a little...

Any timeframe on how close to the Doxie schematic is to being released? I want to increase the top end of the pedal so it isn't so dark sounding straight into my Helix. -Sean

TS5 into the Plexfeta(TM). Switched back to 1960A speaker emulation. Everything on 10 (max) except Volume (output level) - Recorded directly into Reaper using a UAD Volt 276 and Line 6 Helix Native software for speaker emulation, no eq or effects - Speaker emulation used on -01: Dual 4x12...

Here's a favorite setting on the Plexfeta that I think shows a good dynamic capability from fairly dirty to clean. - Recorded directly into Reaper using a UAD Volt 276 and Line 6 Helix Native software for speaker emulation, no eq or effects - Speaker emulation used on -01: Dual 4x12 Greenback...

TS5 (only TS that I have on hand) into the Plexfeta(TM). Switched to Greenback 25 speaker emulation. Everything on 10 except Volume (output level) - Recorded directly into Reaper using a UAD Volt 276 and Line 6 Helix Native software for speaker emulation, no eq or effects - Speaker emulation...

Evidence Settings: Everything on 10 except Volume (output level) - Recorded directly into Reaper using a UAD Volt 276 and Line 6 Helix Native software for speaker emulation, no eq or effects - Speaker emulation used on -01: Dual 4x12 1960A, stock settings (mic: 57, Position: Cap Edge...

After building my first Mofeta board and playing around with it and letting my bass player use it (and ultimately keep it), I decided to make a second one. I made provisions for a few tweaks but ended up using the stock components for that build as well. I have really enjoyed the different...

Gator, Yes, I noticed that the Malachite was darker in tone than the other two Revv clones. I built a Sanguine with the gain of the Malachite but the standard Sangune tone stack. Gave a much brighter sound, so much so that I had to dial the treble down to almost 9 o'clock to stop my ears from...

Hello Everyone, I've been on a multi-pedal kick lately so I made this up for my bass player. He loved the growl and tone of the Mofeta but wanted something to kick it a little and get some nice dirt. So, I took his Mofeta and made it always on and then added the Kliche mini SE (with Chuck D...

I just finished up re-boxing my Paragon Mini. I needed a smaller enclosure so it could fit on my pedal board. I found the 1590B3 encolsure and I modeled it in Solidworks to make sure it would fit. I had to find smaller toggle switches since the old ones would not fit. I found some subminiature...

@iamjackslackof Solidworks is the 3D modeling (CAD) software that generates the models. Then you need a CAM software to generate the toolpaths that are used to ultimately generate g-code (what the CNC controller uses to run the mill). I used the Arduino IDE to write the code for programming...

@iamjackslackof My cnc setup for pedals is just a small taig mill. It has a large enough work envelope that I was able to mill out all of the holes on both the front and top mount jacks/power. When I drilled by hand, I noticed my drill bit wandering ever so slightly and that caused the knobs to...

All, Thanks for the kind words. It is nice when a plan actually comes together in a surprisingly good way. iamjackslackof, I tried drilling my first few enclosures by hand and I wasn't happy with how accurate my drilling was. Now I don't drill the enclosures. I mill them on my cnc mill. I take...