Search results

So do you think this would be possible with the PPCB DPDT intelligent relay board with a custom written ATtiny?

My attempts at burning ATtiny have been less than fruitful.

I think the easiest would be just 1 press to cycle to the next state. Doing # of taps per channel/state would def be cumbersome.

Having ideas and need to get suggestions. Ideally this would be a 4 state intelligent relay channel switch off one footswitch. Want to use it for toggling 2 fx loops, state 1-both off 2-loop 1, 3-loop 2, 4-both on. Having the ability to have LEDs corresponding would be exceptional. Anyone seen...

Ernie’s ball sacks 10’s because I can get them cheap in a 3 pack on Amazon

Wavelord + Glasshole 🤌. Have also used the Wavelord to drive modulation on a Parasit sonic reducer. It’s pretty cool, but less than I had hoped. The mill marks on the HP add to the “creeping damage” aesthetic.

Get some old boards out of broken electronics and practice your desoldering and resoldering. Get a decent DMM and measure every part. double check your BOM before you place parts and cover over the silk screened ref des or value. Only do one value resistor/cap/board at once. Ounce of prevention...

I think the Rook/Bastion may be a Timmy derivative

Got a friend who does all the 80-90s power ballad/metal type stuff along with wedding singer. Plays a Les Paul and dual humbucker fender into a Marshall. His go to is a BD-2 into a Mojohand Rook (PPCB Bastion)

Nice execution! Need some good knobs for that bad boy. love the FilterFX. Especially good with bass and an expression pedal

https://www.pedalpcb.com/product/jfetbuffer/

Thanks for that. I followed the docs as far as adjustments settings and have gone over the board a few times to ensure I didn’t pull a dumb, but it has been awhile so may be time to go back and open it back up.

Damn that’s nice! Gotta ask though, were you able to get trim 1 to bias down to the suggested 6.18-6.2v? I and a few others have discussed the inability to dial it in so that the envelope is active.

Plenty of talk around here about how big everyone’s backlogs are so you are in good company. I think @Feral Feline and @Bricksnbeatles are the top contenders

Why DEFX gotta be that way!? Nice execution of a bitch of a board. I presume this is their Lovetone Ring Stinger board? Finished AionFxs Neurotron not long ago and it is a shit ton of fun esp with an expression pedal. Unfortunately, there is little love to go round for the Ring Mod in this place

Working on finishing up my Xenotron build and am at the point of measuring/installing the LDRs and LEDs. Given what is discussed here, should I just forego the water clear for LED 4 and go with a diffused instead?

Finished up the Duality/Binary build today and it is really cool pedal. Works great with the active Ray. Love the almost wave folding fuzz a la the prunes and custard. One fun thing I discovered by accident, if you run it off a dying battery (ab 7v in my case), you can get this intermittent...

Definite possibility. Was looking at the colossus or ungulate fuzz since both have the mids pot already integrated. I would omit the switch on the colossus and increase input/coupling/output caps to 220nf and remove the first stage diodes. Since my beloved Rhinosuar uses BC549c, I would just go...

Unsure of the diode config in a Bass Muff, just referencing the number of gain stages. I just did a litttle shoot out between the Dizzy Tone, Unpleasant Surprise, and my modified NYC Muff with diode lift and mids pot mod. All performed admirably. The US has a great square wave fuzz to it, so a...

But then it’s just a Bass Muff🤣. I did build the GPCB version and Barry did include a recovery stage, but I can’t recall it really adding anything. I’ll let you know ab the Dizzy Tone here in a minute, but keep in mind it is a 3 transistor circuit as well.