Search results

  1. M

    SOLVED Lead Solder 16mm right angle pcb mounted Potentiometer

    Any chance you didn't print your drill template at 100% full size (like maybe you selected "zoom to fit" or something instead of "print at 100%")? It's the standard PedalPCB 6-knob layout but with one extra hole for the "Deep" switch, so unless you were working off of an inaccurate drill...
  2. M

    Fuzz Face Mod

    Aion's instructions for their Solaris board say "Set the Contour knob just above 9:00" when biasing, I vaguely remember an earlier version of the board specifically saying they'd borrowed the "Contour" control straight from the Fulltone 69 so I'm assuming just above 9:00 was the case in the original
  3. M

    Catalinbread entering DIY market?

    Annoying they went with wires for the DIY kit but use long-pin pots on their own pedals. Saves them maybe one or two cents per pot to go with solder lug?
  4. M

    Catalinbread entering DIY market?

    The pots are wired off board - the *most* annoying way they could’ve gone with off board wiring.
  5. M

    Sunflower mod for EMGs?

    I've seen that done before, usually marketed as passive "unbuffer" pedals (I found more than few just searching "unbuffer" on reverb), but they usually don't have the trimpot after them so that'd be a nice addition if you were gonna build one
  6. M

    Sunflower mod for EMGs?

    Oh yeah, putting it external would be a very smart move since you lose the volume-pot interactivity when you put in a pickup simulator after it, so you'd have to use the "input" trim for that (which would be after the pickup sim but before the FF circuit) to do that (that's why the AMZ page has...
  7. M

    Sunflower mod for EMGs?

    It's the low output impedance of the active pickups that are interacting badly with the Fuzz Face's low input impedance and making it sound funny, same as if you put a buffered pedal before a Fuzz Face Adding an AMZ Pickup Simulator in front of the fuzz would make them play much nicer (check...
  8. M

    NSL-19M51 ROHA noncompliant/contains lead?

    That’s why Fender can’t put its opto tremolo (well, “vibrato”) circuit in the reissue amps they sell overseas, isn’t it?
  9. M

    Lead Solder Overdrive

    Oh I meant the kind I can print out and tape to the enclosure to drill myself but thanks!
  10. M

    Lead Solder Overdrive

    Is it possible to get the Drill Template for this one?
  11. M

    Re: Indiana Tweed / Deluxe Bias

    4-4.5V on the drains. I can't find the source so it's entirely possible I'm misremembering, but I swear I read somewhere that because the originals didn't have trimpots, Wampler would basically spot check (and swap if necessary) JFETs to make sure they were all biased at 4V or higher, anything...
  12. M

    Missing Build Docs / Schematics

    Might be available in a few days https://forum.pedalpcb.com/threads/soldano-slo-overdrive.14126/page-5#post-253219 The BoM cheat sheet is here https://forum.pedalpcb.com/threads/lead-solder-overdrive.20256/
  13. M

    Top Control KoT

    I’ve also thought off-and-on about doing one of these with all top-side controls (and probably in a vertical 1590BB), to save space and make it easier to use I was gonna implement the clipping as a single switch (soft clip/no clip/hard clip) similar to the PoT/Pauper since I’m pretty sure most...
  14. M

    Cast Iron

    4559
  15. M

    Cast Iron

    Agreed! I mean I guess if you’re only making 100 of them and you know you’re gonna sell them out before anyone even has a chance to watch a demo, no sense in sending one to Andy or Mike Hermans, but still. Anyway, if ya love Timmies, I can’t imagine *not* loving this one.
  16. M

    Cast Iron

    This is one of those “god dammit. Gotta give credit where credit is due” posts, because this circuit is “just” a Timmy with an active mids control. And it sounds *fantastic*. Yeah, it sounds like a Timmy, but with little nips and tucks to the tone shaping that make it sound a bit more open...
  17. M

    Dual pedal: (independent + master) switch

    Sorry it's ugly (ignore all the blacked-out bits, of course, only pay attention to the red and white), but I *think* this should do what you want (someone please double-check me though). The left foot switch is the master (hence why its outermost pads are hooked directly to the input and output...
  18. M

    The correct orientation for the keyway slot in a 3PDT is...

    Well now I'm a down-notcher just out of spite. (jk I was a down-notcher from the get-go and wasn't aware the currently-tied vote was gonna bother me this much???)
  19. M

    Aion PCB's

    I hope AionFX never stops making their “legacy” boards, those are among my go-tos for when I need to fit two 1590B-sized boards in a 1590BBS, no breakout board required on ‘em 110%. And the tracing journals are gold. I actually used his trace of the Nordland ODR-C to make a board that was...
  20. M

    Aion PCB's

    Dang, shipped from Japan *that* quick?? Or do they have some secret US distributor I missed
Back
Top