Search results

  1. BuddytheReow

    Pop Quiz (wiring question)

    PPCB “standard” is IN, GND, SW (9V), OUT in that order. You’ll need to cross a few wires on your board to match
  2. BuddytheReow

    TUTORIAL Circuit Block - Booster - Super Hard On (SHO)

    https://www.pedalpcb.com/product/cracklejack/
  3. BuddytheReow

    Breadboards and steel sheets question

    Grounding, maybe? Or a rf shield? Pics might help
  4. BuddytheReow

    More jokes

  5. BuddytheReow

    What’s on *YOUR* workbench?

    Did you spray paint those stripboards?
  6. BuddytheReow

    Chauffeur OD/Daily Driver Zener selection

    It will "work" in the sense that it will be a functional pedal/circuit. A comparison would be the difference between 4148's and LEDs for the clippers. They will both "work" but will sound different. You could always socket the components and switch em out when you're ready down the road.
  7. BuddytheReow

    Double Muffin Fuzz-- Two Big Muffs in one box

    This is going to turn into 2 blendable Muffin Factory circuits with a series/parallel switch.... Just saying.... https://www.pedalpcb.com/product/muffin-factory/
  8. BuddytheReow

    More jokes

    First night of Hanukkah was last night. For those of you who celebrate…..
  9. BuddytheReow

    More jokes

  10. BuddytheReow

    More jokes

  11. BuddytheReow

    What kind of pot is this?

    Thanks. With my DMM it’s a C1M with an odd taper
  12. BuddytheReow

    What kind of pot is this?

    No not yet. I've only had 10 min go go through everything on my kitchen table. When I have a moment I'll put it through the DMM
  13. BuddytheReow

    What kind of pot is this?

    SBP sent me a goody bag and am finally going through it. Can anyone tell me what kind of pot this is? It's a 16mm pot, but just odd labelling...
  14. BuddytheReow

    Do you have a one-knob TL071 boost?

    Good news is you can breadboard something using a simple inverting opamp configuration. I will refer you to the first half of the Mini Muffin schematic plus the power supply section. The pinout for the opamp below is for a dual, not a single such as the TL071. Replace R4 with a output coupling...
  15. BuddytheReow

    What's in the mailbox? 📬 📦

    Sometimes you get lucky. Sometimes you don't. If you don't ask, you don't get.
  16. BuddytheReow

    What's your current headache?

    Going rogue, I see...
  17. BuddytheReow

    Can someone help me with running two LEDs in a pedal?

    the "best" answer is to breadboard it. 2 LEDs can share a single current limiting resistor. In terms of the resistance amount that depends if you've got the superbrights or not. Start with 1k and work your way up from there. Don't be surprised if using superbrights that the resistance goes up to...
  18. BuddytheReow

    What's in the mailbox? 📬 📦

    Speaking of Stompbox Parts, here's a small order I put in for a few parts I misordered from Tayda. No, I didn't "Triple Check" my Tayda order before submitting, so lesson learned. But, wait! There's more! I then asked @StompBoxParts to "Surprise Me" in the order comments section. Christmas...
  19. BuddytheReow

    Is the muffler supposed to clamp all the way?

    Not sure if really an "issue" since it's meant just to kill the "hiss" from other circuits. I've got this pedal and it does a decent enough job, but not enough to say "this is the only noise gate I'll ever use". I do want to try out a Muzzle and compare, but THAT chip is holding me back.
Back
Top