Search results

here you go. I looked in my history on Amazon. I bought them in 2017. That means I have been using these for 9 years. Worth every penny. https://www.amazon.com/gp/aw/d/B00776SKB6?psc=1&ref=ppx_pop_mob_b_asin_title

Well scratch that. I had a min. You can obviously do it however you want but this is how i would do it. As with all the stuff double check me but that should be much closer. https://drill.taydakits.com/box-designs/new?public_key=VDZDVWcxczlwbjZaKzNZUEEwb1R3UT09Cg==

So i guess the big thing here is what do you want to accomplish? Do you want to use all the pots as they are meant to be used, board mounted? If so then your numbers are off. I can work something up but it will take me a few days most likely. I may be able to do it tomorrow but no promises.

That works. Just at a glance the knobs look pretty far apart. I will have to look at it later when I am at home and can actually do some measurements. Also the LEDs for that board are mounted towards the top not the bottom. You would have to wire them off the board to put them where you have...

I tried to look and it just took me to a blank template. You have to use the share link from the drill templates home page.

I use the klein tools katapult Erik shows first. That thing is awesome. It wasn't cheap though and i am pretty sure i had to buy a small set of jaws for it. That being said its the only wire stripper i have used for the last 7-8 years.

So it’s hard to see in the pics but are you sure you mounted the ldr in the right direction? Also you should always use sockets for your ics. If there is an issue with them you want to be able to change them easily and they can be damaged by the heat pretty easily.

So I will say this, you used to be able to order just the standard tubes from amplified parts and be okay. Now you are much better paying the extra couple of bucks to get tubes that have been tested for low noise and performance. Take that for what it’s worth but that’s just my 2 cents. I won’t...

The op07 can be easily sourced from stompboxparts or tayda. Tariffs may be rough for tayda depending on where you live. If you want while you wait you can do some reading and search the web for the op07 vs the lm308. I will spoil it for you though, you can’t hear the difference.

Yeah the other thing that stands out to me on that is the footswitch has a white outline where it would go. That’s usually on the side the switch/part is mounted on. It may work upside down but I don’t think it will work properly.

Power is important with these pedals. I recommend a 1 spot. I would still check the footswitch board. I have never built a c2c board that didn’t have it labeled on top. (Just my experience). It usually says c2c and has a board label like TB or BO. Maybe there are some that don’t. He also usually...

Your footswitch board is upside down. The writing should be on the top so you can read c2c. Not saying it’s the only problem but it is a problem. You will likely need to order a new board as getting a footswitch off without damaging it can be a challenge.

This is the template above.

Here is a template from tayda with the cutout for the jacks and power. I use them on all my builds. Jacks are cheap and it looks nice. https://drill.taydakits.com/box-designs/new?public_key=eUl2NnRrM1NFQ3Rnc3JuK29lVk1zZz09Cg==

Here you go. This is based off the template so verify measurements on your physical board. Led is 3mm with no bezel. Adjust to taste. Power jack is for smaller style. https://drill.taydakits.com/box-designs/new?public_key=cmVOV0lOSmxLU3NaY2EwWTIybVd3dz09Cg==

I was bored and knew this would just take a min. The led is a bit further down than most but this is where it is on the drill template. Adjust to taste. It’s a 3mm led with no bezel. https://drill.taydakits.com/box-designs/new?public_key=aDVYTXFqeEZJWS9lQ2VQREErSElFdz09Cg==

Yeah, I was going to suggest digging around and looking at Robert’s other boards for ideas. He uses standards for most things so it’s likely portions appeared somewhere else on another board. I am happy you figured one out.

I will do my standard and give it a few days. If no one has one I will create it.

I will get you one if no one else posts it the next few days. It should just be the normal 3 knob template without the middle pot.

There isn’t a posted build doc on them so unfortunately at this time you will have to create one using the actual board. When there is a build doc I can create one.