Search results

Thanks, Feral Filine. TY-250P Datasheet https://eu.mouser.com/datasheet/2/410/TY_250P-1892894.pdf

If I remember well, the inductance of the part that looks like resistors and capacitors are too small. I know just this kind of transformer have the characteristic that can "emulate" pickup. I include this, too. It can help to go close to the pickups specific. Generically, the inductance is a...

I bought that transformer, but I still didn't built the pickup simulator. I have to say I afraid about the frequency range, too. And, because another kind of project, I'm finding other transformers, just a bit more expensive with wider frequency range, like: 60Hz - 25kHz or 20Hz - 20kHz. Do you...

Thank you Hamish. If I have to build a Rat I'll give a chance to your layout. About the other layout, the one owlexifry used (by TagBoard blog) I always keep my wires short, but like someone else I got that issue. Somebody else not. I don't know why.

Is there a document of this project? I can't get it anywhere, and I would like to take a look inside, please.

When I built the Rat using this layout I got oscillation problem at higher gain setting using the bridge pick of my guitar, during the first test of the board before put it into the box. A lot of people got it. And you?

The schematic I posted above seems do it. A Phase Switch. Though the transistor is a JFET, not a BJT. It has some little implementation, too, but it has the switch.

That "+" is for the red LED, it's just on the right. :)

That Tetsuo pedal sounds huge? Excuse, but what does exactly it is? Edit: It doesn't matter. I visit your youtube page. :)

Maybe you could take a look at the waza craft version schematic.

I tried the Muzzle in the loop effect of my Laney LC50 and with the DIY Tonemender by ROG used like preamp directly in a solid state Crate amp (I cabled the Muzzle between the preamp and the power amp). In both the case the volume preamps are clean and low volume, just to test it in my room. I...

I'm sure enough the problem is not the buffer in front, TU-2 or my DIY buffered splitter (op-amp based). This pedal needs a splitter to use the key input. I heard if it's a buffered splitter is even better. The Muzzle is a replica of the Fortin Zuul, and the Fortin has a pair of buffered...

I still didn't solve my problem, exactly that you described: I was going to finished up my build putting the PCB into the box anyway, because I thought the issue was caused by the loop effect of my Laney LC50 (I heard somthing like that with a Mesa, I guess). But after the last comment I have...

Hello, I'm looking at the fuzz part in the schematic, the downer part: two op-amp stages (non.inverter and inverter), then the Big Muff tone style, and the recovery stage. Just that makes all that the fuzz sound?

I think you can increase R4 - 390R to set the minimum gain lower. Maybe you can try with 1k resistor. The overall gain will decrease, too. Pay attention, you could lose a bit of volume, I guess. So maybe you have to push a bit the second stage.

I tried it on the emulator software and that doesn't work. Maybe there's still something wrong in your schematic. I advice to open a new thread about it. Maybe somebody can see what's this mistake, if it is there. EDIT: I guess there's something about the bias of the op-amp. Check R1 and R5.

Well... I wish! :)

This DS-2 unverified layout is mine. :p http://guitar-fx-layouts.238.s1.nabble.com/Boss-DS-2-vero-layout-Finally-td50453.html I omitted the Turbo Mode, because I didn't understand the schematic.

First Research: DS-2. :rolleyes: Just kidding!

Is the input sleeve not connected with a wire? Are you sure that is in contact with the ground? Maybe I wrong, but I'm afraid the paint could isolates it from the ground.