Search results

Been on a parallel dirt box kick, and someone happened to request on of these, but wanted it louder with a bit more range, so here's what I did Mods - All caps in signal path increased from 22n to 47n Fuzz transistors are 2N4123 (Q1 hfe 87, Q2 hfe 74) C8 reduced to 22n R2 reduced to 1k R13...

Stock except the diodes (infrared, 1.1vf), dirt pot (100kA), and obviously added the bits for two channel. Eddystone 1590J box, Brutalist knobs, white ink Its simple, it's heavy, it's EQ control spans from flat n middy to scoops. Doesn't do clean boost, but it does awesome distortion through...

Any chance we could get a Low Tide Mini build doc, or at least a resdef layout?

Reverted all the other mods on this second Otolith, and used some Rohm 1S2473 diodes measuring about 0.62 vf

I haven't noticed that, but I'll try to get the other one back from my mate and do a head on comparison

Built mostly stock, the only mods being - R5 is 100r to saturate the chip a teensy bit more C12 is 27p to accommodate the chip swap Chip is an LM308 from Polida (fake? 🤷🏻 sounds good, either way) Drive is increased to 100k Toggle switch added to swap the stock silicon's for red LEDs or no...

Here's an updated take - Basically as described above, but I reduced R2 to 1k, and this one uses a particularly noisy HT8970

With HT8970

With HT8970

This was originally just going to be a Turbo Rat featuring the Soviet UD1408 and glass LEDs, but I had to make some further adjustments to compensate for how dark the chip turned out to be. You'll notice the chip is upside down- I bought a couple dozen of these from a guy in Ukraine, and...

Was just coming here to suggest this. The Klon and DRV stack beautifully. The Rat also takes the DRV well. If you want even more fuzzwall, the DRV also plays incredibly well with just about every Muff variant

Here's one I built a while back, and kinda forgot about. Someone just requested a demo, so I'm sharing it here, too Board is a clone of the Grind Customs Ultra 78, drawn up by our own @jimilee. No mods, except I used Soviet KD522B diodes which have a slightly lower forward voltage than 4148 /...

I'ma check and see if I have any Nanologs left 🤣

But, I wanted to use these diodes I never would have otherwise 😭. I also like having that side be just a tad more responsive to dynamics. I'm still loving the shit out of this guy. Can't wait to take it to our next practice sesh. I gave one to the other guitarist 🤘🏻

Didn't feel like making a new thread, but here's the Peacock going on my board. Slightly modified - C12 increased to 4.7n to allow a smidge more bass through the HP side of the tone control C9 & C13 increased to 27n and 47n respectively to allow a miniscule amount more low end through the...

You should definitely give this and the Tape Delay a go. I'm enjoying both of them much more than the Clarinot. I've got a tweaked HT8970 build of both on my bench that might be making it to my board

I honestly don't really have a preference, unless we're talking the Aion daughter boards which can eff off straight to heck. I do like the freedom of placement that no daughter board gives, though

I've already done a few of these to my (not-yet-boxed) modified take 🤘🏻

Its a PT2399 delay with some awesome tricks up its sleeve, including an envelope driven modulation section and an adjustable tails feature. Capable of barely there slapbacks up to testing my patience, it's got a decent range. I'm especially fond of the way the Noise, Feedback, and Wobble...

Wibbly wobbly wacktastic modulations abound here. Its a chorus / vibrato / slapback that has the ability to modulate the delay time based on your picking strength. It doesn't feature a typical LFO, but does feature a high pass boost that offers up some great textures and adds a bit of lo-fi...