Search results

Yeah. When I first picked the DasiySeedProjects multi-fx up, I’d expected to pick a couple of effects to load and basically have them run in a chain with a default order. It took me a minute to realise it was “one at a time” but I could have dozens of them available in the firmware. To be...

I was thinking about it a bit more and I realised that my limitation was basically NAM + Dattorro and I didn’t really put too much time into NAM + IR, since the NAMs I tend to use are amp+cab generally. I also have 2048-long IRs by default (from the Mulebox), which is probably unnecessary. I can...

It will help the IR loader marginally (but that was not CPU-constrained anyway). It does nothing for the NAM code I think, which is already optimised (this was from DaisySeedProjects originally – I think maybe contributed by you :)

Hi, With NAM A2 + Dattorro at 48Khz and after a bunch of optimisation, I ended up with 98% CPU. That was a bit too close for comfort. I could not get NAM + IR + reverb (which is less of an issue, I think, since most of the NAM models are amp + cab, not amp only). I think from memory, NAM...

I haven't tested it but I don't see why not. It's a generic IR loader so as long as you have a suitable .wav file it will play it.

Yes’s it’s the same reverb. The only difference is that in the Mulebox it runs at 48Khz but that was too CPU intensive alongside NAM so it runs at 24Khz here. It sounds subtly different but still good. @xconverge - Very cool that you made the Mulebox. Would love to hear more about how that...

For fun, I’ve made a pedal based on the excellent DaisySeedProjects 125B @kshep hardware. The code is open source here: https://github.com/optilude/AmpSim You can load it up (at build time) with up to 128 (I think, I’ve not actually tested more than a dozen or so) either NAM A2 amp+cab captures...

I don't have the Terrarium hardware yet (it's on order) to test it, but I've been playing with a fork of the code. https://github.com/optilude/DaisyCloudSeed/blob/ux-updates/petal/CloudSeed/cloudseed.cpp All I know for now is that it builds and deploys to the Daisy Seed. :) But the idea here...

Did you paste the source code? Maybe describe the steps you took (ideally with screenshots)?

Update 22 September 2026: All new versions that are self-hosted. You can download these and use them on your local computer. This post contains two tools that can help you keep Tayda Electronics drill templates and UV templates in sync. Tayda to Artboard You have created a drill template in the...

I’m going to try to build this. @scott3t - a bit alarmed you managed to fry your Daisy Seed. Any idea how? @keyth72 - in the demo, I couldn’t figure out how to tell which preset is currently selected from the right foot switch. Do you just have to hear it? Does it save between power cycles...

This is mine. I used the drill template from this thread but rebuilt it using the new Tayda “shape” cutout option, which made it easier to translate to a visual design. This is the drill template I used. You’ll notice it uses a 5mm LED bezel (also from Tayda) with a wired-in LED. I used Tayda...

Hi, I’ve built the EV mini and it’s super cool! What strategy / method should I follow for biasing using the two trim pots? Am I looking for a particular behaviour on the bulb, or is it all by ear? Is the sound likely to be affected much by ambient light (ie do I want to close the back lid...

An old thread I know but … For “unity gain”, I think the resistors to change are R2 (bottom right side of top board) and R4 (bottom left side of top board). However some of the quoted posts above mention R1 instead of R2 and even go so far as to talk about R1 being near R4 (which it is)...

Hi, (Please move if wrong forum) I wrote a guide for using the Tayda UV printing service with Affinity Designer 2 (I used the iPad version). It was aimed originally at the Jeds Peds community but very little of it is Jeds specific. I learned a lot about how to do it from this forum. Hopefully...

Amazing :) Which app did you use to check for the layers on export?

Hi, I’m trying to create a design for Tayda’s UV printing service using Affinity Designer 2 on iPad. I’ve followed various tutorials and forum posts, not least this one. I believe I have a file in Affinity that conforms. It has three (visible) layers: WHITE, COLOR, and GLOSS-M. It uses CMYK...