Search results

That came out nice. Is the faceplate brass you shaped and put water slides on? If you do another build you want to post there is a build reports section.

Isn’t the gain of an op amp with negative feedback increased with resistance? What about changing R7 to something like a 10k? The palisades and dunes which are TS variants use a 22K and 10K in the feedback loop there.

I haven’t done this but the program selector switch is a SPDT on off on switch so its programs would be top 2 pads jumped, nothing jumped and bottom 2 jumped. Alternatively have you considered installing the switch on the other side of the board and just leaving it in the box?

Nice work on your first successful build!

I messed with this for a while today on my production pedal. I was pretty happy with a B500k wired as a variable resistor between lug 2 and 3 of switch 1. I think an A taper could possibly be better but I don’t have one on hand. I’m going to include it on my board instead of the switch when I...

Sweet builds! Those are the first 2 pedals I ever owned. I was hoping the Aion with the expanded control from the original would work better. I will probably have to build one myself just to be sure:ROFLMAO: .

Really nice build. I like the graphics and color scheme. I look forward to the demo.

This pedal represents a few firsts for me. It is the first board I have had manufactured and it is the first build I have done that was designed by a forum member(who isn’t Robert). I pulled this board out Sunday night as a way to relax. It was an easy build it took me about 2 hours from...

Here are some links to the 3D printed parts on this pedal. Hex knobs 2x12.5MM washer 3PDT spacer and LED holder

I designed and 3D print the holders, also a few washers and the knobs. I will post some links to them later today when I get a few minutes.

here is my Duo-Phase. This is probably my largest build so far but it was honestly pretty easy. Other than a slight mixup with an IC and charge pump it fired right up. Quick adjustment of the trimmers and it’s good to go. I haven’t owned a phaser before but I really like using this one...

Very cool unique build. Awesome job!

This thing is a pretty interesting pedal. I like the slower settings they add a lot of nice color and variation. Mine is fairly noisy with kind of a static wind wooshing type sound. I am going to try shielding the input and output wires and maybe changing the few black caps to JRBs...

I have done a few that have a mix of hard and soft clipping. This one actually does even. The ODC knob on this gradually takes you from compressed turned left to harsh/grit/open turned right. I’m curious if there are any pedals that have this for hard clipping. Like could I put this on a...

Has anyone on here experimented with replacing switch 1 on the Carcass with a pot? I have the board coming and think I might prefer being able to do the in between settings. I was thinking a 1 meg pot as a variable resistor between lug 2 and 3 might be the trick but have also considered that...

Here is my second Aion board. I really like this one. The controls were a little confusing at first. I actually read the manual for it which I normally don’t need to do for a drive pedal. It can do scouped or boosted mids and the ODC control offers more fine tuning of the soft clipping than...

You’re good. I just haven’t sourced any yet. I have 4 strand and the kind with foil but feel like it would prefer this. I don’t think Tayda where I normally buy stuff has it unless I’m mistaken.

I think my pedal building break is over. This is my first non 3d printed enclosure other than the Particle Accelerator which came pre drilled. I had fun getting to use my drill press making this and my layout tools to mark it. I went with the Galaxie Mod and I’m happy that I did. I...

Anyone know of an affordable source for shielded wire like this? The mixer I’m rebuilding has a bunch of it inside and I feel like I would like it for wiring ins and outs. Seems like it would be easy to work with. 22 or 24 gauge would be my preference.

I have done a bunch of 3D printed enclosures myself. I think it is neat seeing someone come up with a different solution to the same problems. I really like the way your artwork came out on yours. I have also gotten the feedback about them potentially being weak and although the designs I...