Search results

I tried the Muzzle in the loop effect of my Laney LC50 and with the DIY Tonemender by ROG used like preamp directly in a solid state Crate amp (I cabled the Muzzle between the preamp and the power amp). In both the case the volume preamps are clean and low volume, just to test it in my room. I...

I'm sure enough the problem is not the buffer in front, TU-2 or my DIY buffered splitter (op-amp based). This pedal needs a splitter to use the key input. I heard if it's a buffered splitter is even better. The Muzzle is a replica of the Fortin Zuul, and the Fortin has a pair of buffered...

I still didn't solve my problem, exactly that you described: I was going to finished up my build putting the PCB into the box anyway, because I thought the issue was caused by the loop effect of my Laney LC50 (I heard somthing like that with a Mesa, I guess). But after the last comment I have...

Hello, I'm looking at the fuzz part in the schematic, the downer part: two op-amp stages (non.inverter and inverter), then the Big Muff tone style, and the recovery stage. Just that makes all that the fuzz sound?

I think you can increase R4 - 390R to set the minimum gain lower. Maybe you can try with 1k resistor. The overall gain will decrease, too. Pay attention, you could lose a bit of volume, I guess. So maybe you have to push a bit the second stage.

I tried it on the emulator software and that doesn't work. Maybe there's still something wrong in your schematic. I advice to open a new thread about it. Maybe somebody can see what's this mistake, if it is there. EDIT: I guess there's something about the bias of the op-amp. Check R1 and R5.

Well... I wish! :)

This DS-2 unverified layout is mine. :p http://guitar-fx-layouts.238.s1.nabble.com/Boss-DS-2-vero-layout-Finally-td50453.html I omitted the Turbo Mode, because I didn't understand the schematic.

First Research: DS-2. :rolleyes: Just kidding!

Is the input sleeve not connected with a wire? Are you sure that is in contact with the ground? Maybe I wrong, but I'm afraid the paint could isolates it from the ground.

Hello, I was thinking to build a variable voltage pedal like your. But I don't like the voltage range: ~7.5VDC to 1.25VDC. The minimum 1.25v seems to me very small. Maybe a smaller pot, 2k, will drop less voltage. But what I want to solve is that starting drop voltage of 1.5v. My ideal range...

I noticed that DHL shipping starts at about 12 $, but filling the cart is was about 8 $, then almost 10 $ (no enclosure). There's still the fee, that is a mysterious! But now there's an option that includes shipping and taxes. It costs more, but that said: «GOOD DEAL!!! Duty and Tax Prepaid -...

I didn't find any transformer's datasheet with the inductance value. I just found this chart, and this very interesting picture: Thanks for the measurements!

And what about the inductance of the TY-141P? I can't find this information.

My first Muzzle (original THAT chip, no smd), I remember, with the 4 Cable Method, I set the Threshold enough to cut the excessive noise of the distortion perdal (DIY Triple Wreck), but when I bypass the distortion the clean was fine. I hope to find my friend and try that pedal.

So your clean sound is save and not gated? Did I understand?

Your voltage measurements look very close to mine, I guess. I'll check the voltage of my PCB soon. I'm connecting the PCB following the Fortin Zuul's manual. I expected more especially from the 4 cables method with Input Key and Loop FX. What happens if you bypass the distortion getting a...

I built it again: new PCB and new THAT4301 RetroFit Module and all new parts from Musikding. But it works bad in a identical way of the first built. So I'm pretty sure I didn't make any mistake on the board. I'm following all the method in the Fortin Zuul manual to insert it in the pedal chain...

I'll take my time to mount everything, I have to include just the Key input, not the side output. With the old built there was, apparently, a bad THAT chip, unfortunately I had to solder it directly (thing I never do, but I had to, this time). Ground and +9v was ok on all the ICs, but in the...

Old thread, but I had trouble with the THAT4301 RetroFit Module, so I build the PCB again. The first time I had to used this new mini PCB I noticed that there's not enough room to fit this mini PCB because the socket IC of the LT1054, and there' not enough room to fit the SPDT next the THAT4301...