Search results

  1. I

    Missing Build Docs / Schematics

    Never mind. I found that schematic in another post from you. Thank you!
  2. I

    Missing Build Docs / Schematics

    Great! Do you have a schematic for the buffer/inverter by chance? Save me from tracing it out to see what's 'going on' in the circuit
  3. I

    Missing Build Docs / Schematics

    Are there any plans to do this in a through-hole circuit board?
  4. I

    Duck Box not quacking

    Fixed. Unsoldered component leg. Must have been making enough connection originally to work.
  5. I

    Duck Box not quacking

    My Duck Box no longer quacks. It's now more of a huge bass boost. Someone borrowed it a while back and I didn't try it when I got it back. I can't imagine him 'blowing it up' somehow. I replaced both op amps. Still doesn't work. So I re-soldered a bunch of joints. Still no quack. Any clue as to...
  6. I

    Blue Breaker silkscreen error

    I should have clarified that the 'picture' of the silkscreen had the parts switched. My bad. I had already populated the board and could not see the actual silkscreen without lifting components.
  7. I

    Blue Breaker silkscreen error

    I don't see anywhere that this has been discussed, so... on the Blue Breaker silkscreen, the values for R8 and R10 are reversed. R8 is a 1K , but is shown as a 1M. And R10 is a 1M and is shown as a 1K.
  8. I

    PPCB ADHD 2.0 Germ

    Thank you as well! Great work you're doing here!
  9. I

    PPCB ADHD 2.0 Germ

    Great! Thank you!
  10. I

    PPCB ADHD 2.0 Germ

    Wait...how are you referencing actual part numbers, like C7, R8 etc. if there are no build documents on the pedalpcb ADHD page?
  11. I

    PPCB ADHD 2.0 Germ

    Thanks. That's good info. I'll try a few of your suggested changes.
  12. I

    PPCB ADHD 2.0 Germ

    I wasn't really trying to recreate a specific version. It's just that my Fulltone V1.3 sounds better than the latest pedalpcb version to me. I'll try pulling the Germs. Thanks for the help/ Appreciate it.
  13. I

    SUPA FUZZ how to led and 9v jack?

    Can you post a link for that wire please? I'd like to try that instead of stranded.
  14. I

    PPCB ADHD 2.0 Germ

    To clarify, I just built the 'new' Pedalpcb ADHD version (https://www.pedalpcb.com/product/pcb542/), using the component values shown on the pedalpcb circuit board, since there are no build documents listed yet, and no schematic. MY Fulltone OCD is a Version 1.1, the first one they made. current...
  15. I

    PPCB ADHD 2.0 Germ

    I just finished building this 'new' version, and I need to pick your brain a little, if you don't mind. So, I used the component values on the picture of the circuit board, and 34a's for the diodes. It works, but it's a little on the 'trebley' side, with not a lot of bottom end. If I turn the...
  16. I

    wire preference..

    Thanks for the wire suggestion. I just ordered that, after spending way too much time trying to stuff 22ga stranded through the tiny pcb holes.
  17. I

    SUPA FUZZ how to led and 9v jack?

    I'm pretty sure the tinned wired is not the source of your 'noise' issue. My 2 cents...
  18. I

    PPCB ADHD 2.0 Germ

    Thank you!
  19. I

    PPCB ADHD 2.0 Germ

    There's a mini-slide switch on the ADHD page, like it might be an option, but I don't see a spot for it on the circuit board?
  20. I

    Soldering Belton Brick

    thank you
Back
Top