Search results

Is it working?

I've had this issue recently, I don't see if there is a led already wired into the fuzz pcb, put one in. When I tested this I noticed I wasn't getting power the effect pcb. I was able to fix the problem by jumping the sw and gnd holed on the bottom and wiring them to one of the grounds on the...

That is awesome, simple and exactly what I was looking for. Thanks.

Morning, I've had this pedal for a few months now and have been really enjoying it and made some changes (Tone mod and 18V mod). the only thing that is bothering me is the "clean" mix knob. I know it's supposed to start to break up in its own way, but with my bass it seems to be breaking up...

Did you get the same LED and LDR that the build docs mention from Mouser? I have to say based on the number of posts/threads this is a bit of a finicky build lol.

If you look at my build I ended up omitting one of the expression jacks and moved the output jack over one cause it was drilled too tight. I answered in longer format in my post about the pedal but it's the up position for the moog filter sound.

From what I can tell the fd-1 is a nonmosfet fulldrive 2 with no boost in a smaller case. The minidrive is a fulldrive 2 mosfet with no boost in smaller case. We just have to hope it comes in stock soon lol.

I believe it's in the up position for two reasons. One the quack sounds more round in the up position to my ears and a little bit stiffer in down position. Also even though the docs don't mention it specifically there is a small section that talks about if you want to omit the switch all...

Should have added this, from what I was reading it should be 10k pot a or b? Going in lug 1, lug 2 is wired to lug 3 then lug 3 goes to a 1nf cap then wired to lug 1 of the blend?

I was looking at this pcb for a project idea. Is there a way to interject a low pass filter or just tone pot for the clean signal? So that it will only really mix back in clean bass? Would it be wired directly before the blend jack after c2?

I finished my 3rd and 4th builds. Small con for both of these builds..... holes.... so many holes.... they each have over 20 drill points lol. The xenotron / lovetone flange with no name. I had some issues with this build, you can view my troubleshooting post about it. After that I really...

I calling this one fixed. In the end it's working but once I got it in my bass rig I didn't like it for a few different reasons. Gonna make a build report with that and the spectron.

When I was testing on the pads seemed like i had to move the probe around to get a reading. But it seems to be working now. I'm gonna re bias the regen and bbd tomorrow and hopefully close this.

The R26 was the proper 39k but I felt wierd about the resistor slot itself so I replaced it with a new one. There was no difference but jumping the resistor is making it work correctly. I'm not really sure what the issue but it seems to be with that slot. At the point I don't even know if I want...

So that's what I did and I was able to track modulation all the way up to R26. On the other side of R26 there was no longer modulation. So even though the resistor reads correctly could it still be bad? I did do a reflow on it but didn't replace it.

Just to catch up. Using the mono/Space out Produces little to NO modulation. Using the Time Out /Stereo jack works and produces modulation. If I Jump the Time Tip and combine it with the Space Tip it works and produces modulation. So, based on what I can tell the issues is however the time...

I need to put this on hold for a few days as I melted some of the jacks when i started to de solder everything. Talking to Lace sensor he thinks I just screwed up wiring the swtich jack since I had a signal when I jumped the time tip to the space tip which makes sense based on my rats nest.

I might give the probe a try, just have to make one. But shenanigans is right, reading the schematic makes it seem the transformer only plays a part when the time signal is separated into its own out. I don't see where it mixes back in to the space unless I'm following it backwards around the...

Just hit a breakthrough, I was going through @Kris100 Thread and came across his post where he jumped the time tip into the space/ mono out tip. I did that exact change and boom we have modulation. I just need to re bias since I was randomly moving around to try and fix it. Also one of my led...

I was testing the case and on. I would describe kinda of the same issue you were noting, there is some vague flanging and self ocilation at almost full cw settings. The biggest thing that's getting me is the led on the daughter board, when the time section is off the led seems to be the...