Search results

Swapped capacitors and no better.

C1,c2,c3 do thud.not as loud as the input wire though. But they do in the older one too that doesn’t have a noise issue.

So I went through it again. The input wire is definitely the the loudest wire when tapping on them. Second would be the hot (power) wire. The power wires aren’t really much worse than the older pedal though. But the input wire from the input jack is. So, what do you guys think if I used...

so I picked up a silver label sd-1 to compare to my black label. (Silver is on the right in pic). Volume at 9 o’clock and gain at 8 o’clock (almost off) the silver label has this hum and it gets super loud the more you turn up gain and/or volume. I tried it with a battery and no change. I...

Kindcanuck that looks pretty nice. I like the purple. I was playing mine last week and telling myself this doesn’t sound right. Not like the other slo’s I’ve had. Plenty of gain but it didn’t have those harmonics.Just sounded flat to me. I’m a rock/metal guy lol So I looked at the...

This is definitely a good idea. I’m using a axefxiii and the movement of the pedal turns the effect on/off. I’ll be taking mine apart soon and flipping that metal bar over to check it out.

Great idea. Better than my rubber band trick. The little metal strip that goes over the tread pin and screws into the base. He flipped it over and only screwed the back part down so it acts as a spring and pushes the pedal back up to the heel position.

Here is a few. I used shield around the input and moved a few things around trying to reduce the hum. Update Had a tech go through it and he took the paint off the chassis so the switches and pots were grounded to the chassis and the hum/buzz is gone. So if anyone tries this kit keep this in...

I asked a friend/tech to look at it. I’ll send rosamp a message if he can’t figure it out. Thanks for the reply

Kindcanuk, I just finished a 50w. I’m getting a little hum when I touch the amp. Specifically the overdrive gain knob and the three switches on the front. Are you getting the same thing?

Thanks again everyone

Boy do I feel like a horses azz. I ordered parts for 5 pcb and totally forgot about them being programmed. Anyways swapped chips and all is good. No noise or anything. Well,if you want pm me your address and I’ll send you these 5 chips. I don’t program them and it’s the least I can do...

Update I swapped the 24Lc32a = no change. R5 to ground gave me a reverb/wha sound.

I have searched the forum and found another person with this issue but it was never resolved. Finished my build and have no delay sound.It’s working minus the delay. Mix works,volume works but,nothing else makes a change. Fv1 was pre soldered on board. Tl072 chips came from tayda...

I’ve tried r4 at 2m and no change. I asked where you go your parts thinking maybe we both got bad parts somewhere or maybe even a bad batch of boards.

Where did you get your parts from? I ask because I have a huge volume loss also.

R4 bleeds off some signal. Connected at the input it shouldn’t be a huge difference. So today I printed out the pcb and went over every component one by one. All correct. Flipped it over and reflowed every solder joint checking to make sure they weren’t touching another part. All good. No...

Took them out and measured. 2m. Played the pedal with them out and no difference in volume.the pcb was out of the box also and I made sure it wasn’t laying on anything conducive. Looked over the board again and no crossed solder spots. I’m at a loss

Yes. The volume never changes other than with the volume knob. I took it apart and didn’t see anything that stuck out. Volume pots right. Nothing can touch the board. Triple checked the modded resistors. I may just remove r4 and try that. Remove any signal to ground there.

All my caps are right. All the resistors I checked last week. Only thing I can do is take it apart to double check the volume pot is correct. Maybe play it out of the enclosure.