Search results

  1. H

    Pestle Distortion

    Can somebody tell if 470pF at C8 is correct? I get no signal after it. Swapped another 470pF but no luck. If I short it I get pedal working but only halway working treble.. Thanks!
  2. H

    Lead Solder Overdrive

    How it the sound?
  3. H

    SOLVED Boonar Dawner Prince

    Yes they exist but I've got 0 support for the used pedal. Nobody replied my emails. Lucky me it was a single component issue so fixing that got me a working pedal.
  4. H

    SOLVED Boonar Dawner Prince

    I've managed to get friends functional pedal and poking with a scope in both I've found out that one of the fets was shorted on mine. Replacing that fixed the problem!
  5. H

    SOLVED Boonar Dawner Prince

    Voltage doesn't drop on lower board even if both boards are connected. I get 50C degrees on LF33, It's outputting steady 3.3V so I guess it is normal operation. Otherwise no hot components.
  6. H

    SOLVED Boonar Dawner Prince

    Can somebody tell where to look for a problem?
  7. H

    SOLVED Boonar Dawner Prince

    Hi! I have this pedal with an issue of dropping voltage. Is has multiple voltages inside, 3v, 9, 27 volts. 2 boards interconnected. When I separate the boards, lower one with powersupply holds voltage ok leds on bottom board are working. When I connect upper board, voltage drops in 1-2 sec and...
  8. H

    Simulcast (latest version) semi working

    I have to admit that turning over the cap and reflowing joints didn't help. Still sound is weak. I measure around 80hfe on OC71 maybe that is a culprit? Edit: There is 1uF cap instead of 1nF🤣🤣
  9. H

    SOLVED Simulcast with no clipping?

    Replacing chip didn't help in my case
  10. H

    Simulcast (latest version) semi working

    Hi, I've got same issue with no gain and low output. I'tried different GE PNP from 80 to 150 hFe with no luck. Different transistor and charge pump. I have pin 1 and dot down right, continuity to R10 and R11 are fine. Other pins to ground and to pot are fine. Any clues how to make this work...
  11. H

    DEMO Basstaur (AKA Kliché Mini with Chuckified bass mods) + DEMOS!

    Hi where I could find out about bass mods?
  12. H

    Tis the Season for Mystery Meat...

    Does it have sonically any difference if 4,7uF is electrolytic or giant poly. Is this the one that is paper in oil in the original?
  13. H

    PPCB Mystery meat

    Does it matter what 1N34A to use D9E D9B shottky?
  14. H

    Champ Stamp - Trimmer / Biasing

    I get voltages right with trimmer on Q1 (BC547B)
  15. H

    Champ Stamp - Trimmer / Biasing

    Hello I've got Champ Stamp together but get no sound. With oscilloscope and function generator I get signal until volume pot from input. From output lead to the drive pot. I would need a schematic 😔 I've tested all transistors with component tester and they seem to work. Tried also another ones...
  16. H

    Special K

    I really liked mixing red led with GE diodes with low fV below 400mV. Led gives a singing quality and tight lows germanium high end sizzle Liked this a lot more than original diodes. Switch is not soldered :cool:
  17. H

    Crunch Captain Deluxe docs

    Latest version now has an extra "bright? " switch what you guys think it might be?
  18. H

    Univibe issue - bulb not bright / deep enough flashing.

    Ok I will try this
  19. H

    Univibe issue - bulb not bright / deep enough flashing.

    I have pcb together bug get clean sound no vibe effect? Slight lfo hissing in background. Bulb is flashing and trimmers work, pots appear working. I've tested all 5088 above hfe 600. Tried a different IC. If I install L78L12 oriented as on pcb bulb doesn't flash. Other way around it flashes but...
Back
Top