Recent content by Thomasyoung

After more than 4 months finding for a solution for this pedal work properly I want to share with you how I fixed this issue for all the users. I did a stripboard with 2x 47K resistors and a 250k trimmer pot, Then if you check the schematic R25 goes to Base and Collector and solder as per the...

Hi again, I decided to do a video on what issue I am having with this VIbe PCB I am thinking that can be a stereo Pot failure, but would like to have your inputs, thank you BTW.

Will post here a picture of the stickers, they are the ones Musikding adds on their kits a round black sticker with some height like 2/3mm.

Well, I can do that as well, will try and testing after with more extensive use. No, I add some properly stickers on the back of the Pots below the PCB (y) Normally I expand the transistors leads to fit tight into the sockets.

Hi Sorry for my late reply, I was sick for a couple of days but now I am able to post some pictures. Was playing with the pedal today and the effect never dissapeard before testing I loosen the pots completly. But they were not tight, strange if this can be this the issue ? I will continuum...

Thank you for your answer, and already tried that but same problem persists. Thank you, will upload for sure!

Hi all, Hope you´re doing well. I have an issue with my Abyss. it does the vibe sound really well for some time, but sundently the vibe sound dissapierd. Happens when I touch in a Pot OR if I play it for a while the sound vanish. Tried to change the IC but the same happens. I really liked...

Hey @Giorfida Thank you so much for the explanation, I will probaby buy a UPS/BPS, Can you recommend one that will not cost too much ? I just want to "clean" my electricity from the Power Line. BTW new update, I´ve ordered a new IC TL074 and the new one don´t make any noise even using the...

Well in my case the problem is not the Cioks is more related with the Power Line TP-Link that insert lot´s of noise in my electricity. If I desconnect the Power line TP-Link everything works perfecty, but I need to have internet in my studio, that is far from the router 200 meters. and I cannot...

Was just to make sure the hiss/hum can be noticeable heard just that. Thank you as well for trying to help in these cases all tips are really welcome when we don´t have any conclusion about what causes the issue.

Well I think I know what the problem is now. I was able to reduce the noise in 85/90% or more! First the power supply Cioks is connected to a Power Line TP-Link that adds lots of noise in some type of circuits. (Fuzzes for Example) Than the other batteries I was using was too old. So I...

Another suspicion I have is that the LDRs are of low quality, as I bought a kit and they normally don't use more expensive LDRs I think.

I have 2 plastic covers, pots are not touching the PCB I have 2 plastic covers, pots are not touching the PCB I am using the pedal with Fractal Audio FM3 and it´s a quite silence unit, other pedals I´ve tested with like the Electrovibe and it´s dead quiet. Yes I´ve used a compressor but it´s...

Hi all, Hope you´re doing well, I am having too much noise with this pedal, when I increase the level knob there is a huge amount of noise/hiss that I am trying to figured out what can be but without any sucess at this time. Already check the Pot and seems to be ok, (Deoxit D5 applied too) and...

Will start building the Twin Face in a couple of days, and I will follow these Mods tips on my project, I always like to have my unit volume at 12 o´clock or less, hope these Tip can help with. My "mods" will be for R3 and R7 1k instead of 470R And for C2 and C4 like @Chuck D. Bones recomended...